Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Silly question about Branch Circuit Requirements for Aluminum

User: ul_1973_tested, Location: Chicago

Asked on: Thursday, October 31, 2024 at 5:21 pm EDT
Answered on: Thursday, March 6, 2025 at 4:42 am EST

Question: Hi all,Long time lurker, first time poster.I have what is probably a ridiculous question. In the 2023 (and previous) NECs, table 210.24 - Branch Circuit Requirements - Summary has an entry for aluminum and copper-clad aluminum wires.Is it true that you can wire branch circuits with aluminum wire? Or is that part irrelevant because (a) you couldn't buy NM-B aluminum wire or (b) nobody will insure the house? I'm not planning on wiring a house with aluminum wire, I just didn't understand why it was still in the NEC table and was curious about if anyone ever uses aluminum wire for branch circuits.Are there any houses that are built in the modern era that use aluminum-only NM-B wire for say a 20-amp branch circuit?Thanks all!

That's a great question, and it's not ridiculous at all! The presence of aluminum in Table 210.24 definitely raises the eyebrow. Here's the breakdown

The Short Answer:

Yes, in theory, you can wire branch circuits with aluminum conductors. However, it's extremely rare and generally not recommended for small branch circuits (15A, 20A) in residential wiring due to the potential problems and restrictions associated with it.

The Long Answer and Nuances



Why is it in the NEC?
The NEC is a comprehensive document covering a wide range of electrical installations, not just residential. Aluminum conductors are commonly used for larger feeders and service entrance conductors (think 100A, 200A services), as they are lighter and often more cost-effective for these larger sizes. Table 210.24 applies to all branch circuits, regardless of where they are. The NEC doesn't dictate "you must use aluminum here," but rather provides the rules if you do choose to use it. NM-B Aluminum Wire

You are correct that aluminum NM-B (non-metallic sheathed cable) is virtually non-existent for typical residential branch circuit sizes (15A, 20A). It was more common in the past, particularly during periods of high copper prices, but it led to problems.

The Aluminum Wiring Problem

Older aluminum wiring used in residential branch circuits had several issues:


Expansion and Contraction

Aluminum expands and contracts more than copper with temperature changes. This can lead to loose connections at terminals, which creates resistance, heat, and potentially fire hazards.

Oxidation

Aluminum oxidizes quickly when exposed to air, forming a non-conductive layer. This increases resistance at connections.


Creep

Aluminum is more prone to "creep," a slow deformation under pressure, which can also loosen connections over time.

Solutions (What the NEC Requires When Using Aluminum)

If you
were to use aluminum wiring for branch circuits, you must follow very specific guidelines to mitigate the problems listed above:

Use of Terminals Rated for Aluminum

You must use devices (outlets, switches, breakers, etc.) that are specifically listed and rated for use with aluminum conductors (marked with "AL-CU" or "CO/ALR"). These terminals are designed to accommodate the expansion/contraction and oxidation of aluminum.

Proper Installation Techniques

Tighten connections to the specified torque using a calibrated torque screwdriver. This is
essential to prevent loose connections. Using anti-oxidant joint compound is also recommended.

Insurance and Local Regulations

You are also correct about insurance and local regulations. Many insurance companies will not insure a house with aluminum wiring unless it has been properly remediated (e.g., pigtailing copper to the aluminum with special connectors). Some jurisdictions may have specific restrictions or outright bans on aluminum branch circuit wiring.

Modern Usage

While
rare for general branch circuits, you might see aluminum conductors used in specific, controlled applications, like:

Dedicated Circuits for High-Current Appliances

For a dedicated circuit to an electric range, a large AC unit, or a similar high-current appliance, you might encounter aluminum THHN or XHHW conductors installed in conduit. However, even in these cases, copper is often preferred.

Mobile Homes/Manufactured Housing

There may be some use cases for aluminum wiring in manufactured homes but they are usually larger gauge for service or feeder circuits.

In Summary

While
technically permissible under the NEC, using aluminum wiring for standard residential branch circuits is generally a bad idea due to potential problems, insurance concerns, and local regulations. It's far more common and recommended to use copper for these circuits. The presence of aluminum in Table 210.24 is a reminder that the NEC covers a broad range of electrical installations, not just typical residential wiring, and that you must adhere to stringent requirements if you choose to use aluminum conductors.

Disclaimer:
I am an AI chatbot and cannot provide professional electrical advice. Always consult with a qualified and licensed electrician for any electrical work.* Flag for review

Previous Question Next Question