User: Alwayslearningelec, Location: NJ
Asked on: Friday, November 1, 2024 at 8:44 am EDT
Answered on: Thursday, March 6, 2025 at 4:42 am EST
Question: I believe a "stub/stick" of conduit would be required when running vertical on wall but do the conductors need to be enclosed in a raceway for the entire length??
You're touching on a common question about conduit and wiring practices. Here's a breakdown of the considerations
The Short Answer:
No, you typically don't need to enclose conductors in a raceway (conduit) for the entire vertical run on a wall, provided certain conditions are met. The length of conduit you describe is most likely to be a stub or stick of conduit to protect from physical damage.
Key Considerations and Code (NEC) References
Physical Protection (NEC 300.4(D))
This is the primary reason for using a conduit stub or stick. The National Electrical Code (NEC) requires conductors to be protected from physical damage. A common scenario is where wires exit an outlet box or panel and are run down a wall. The section closest to the floor is vulnerable to kicks, bumps from furniture, or other damage. The conduit protects the wires in this vulnerable zone.
Exposed to Physical Damage (NEC 320.15)
The NEC allows the wiring method to be exposed as long as it is not subject to physical damage. If the cable or conductors will be vulnerable to physical damage it must be protected.
Specific Wiring Methods
The rules vary based on the type of wiring you are using. Here are common examples:
NM-B Cable (Romex)
This is a common non-metallic cable. NEC 334.15(B) addresses runs of NM cable along walls. Generally, it needs protection where subject to physical damage. This is where the stub of conduit comes in.
EMT (Electrical Metallic Tubing) or other Raceway
If you do choose to run conduit for the entire length, you'll need to follow the rules for that raceway type. This might include secure mounting (straps) at specific intervals (NEC 358.30 for EMT).
Height
The height to which protection is required is not specifically defined by the NEC but is commonly accepted by AHJ (Authority Having Jurisdiction) at 8ft.
AHJ (Authority Having Jurisdiction)
Always check with your local building department or electrical inspector (AHJ). They have the final say on what is acceptable in your area, and they may have local amendments to the NEC that are stricter.
Example Scenario
Let's say you're running NM-B (Romex) cable from an outlet box down a wall to a receptacle near the floor.1.
Leaving the Box
The cable exits the box through an approved connector.2.
The Stub
A short length (e.g., 18-24 inches) of PVC or EMT conduit is installed vertically on the wall, starting near the outlet box.3.
Entering the Conduit
The NM-B cable is fed into the conduit.4.
Exiting the Conduit
The NM-B cable exits the conduit near the floor.5.
Down to the Receptacle
The NM-B cable is then routed to the receptacle box.In this scenario, the conduit provides physical protection for the vulnerable section of the cable near the floor. Above that, the cable is considered less susceptible to damage (assuming it's not in a high-traffic area or exposed to other risks).
When a Full Raceway Might Be Required
High-Risk Environment
If the wall is in a location where damage is likely to occur (e.g., a loading dock, a garage where vehicles might hit the wall), a full raceway might be required for the entire run.
Exposed to Sunlight or Weather
If the cable is exposed to direct sunlight or weather (e.g., an outdoor wall), you would need a suitable wiring method rated for outdoor use and likely a full raceway for protection.
Specific Equipment
Some equipment installations might mandate a full raceway for grounding or other reasons.
Local Code
As mentioned earlier, the AHJ can require it.
In Summary:
While a "stub" of conduit for physical protection is common and often required, enclosing the conductors in a raceway for the entire length of a vertical run is not always* necessary. It depends on the type of wiring, the potential for physical damage, environmental conditions, and the requirements of your local electrical code. Always consult with your local electrical inspector (AHJ) to ensure your installation meets the requirements. They can clarify any specific rules or interpretations in your area. Flag for review