Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Kick Space Heater

User: Jimmy7, Location: Boston, MA

Asked on: Sunday, November 3, 2024 at 7:34 am EST
Answered on: Thursday, March 6, 2025 at 4:46 am EST

Question: I have to wire a kick space heater for a hot water heat system in a kitchen. Is the on and off switch on the unit considered its disconnecting means, or do I need to add a switch? Can I bring the romex right to the unit?

Okay, let's break down the electrical requirements for wiring a kick space heater, keeping safety and code compliance in mind.1. Disconnecting Means General Requirement

The National Electrical Code (NEC) requires a readily accessible disconnecting means for appliances. This allows someone to easily shut off power to the appliance for servicing or in an emergency.


The Heater's On/Off Switch



Typically, the on/off switch on the kick space heater itself is NOT considered an acceptable disconnecting means
for the purposes of the NEC. Here's why: Serviceability

The switch is often located inside the heater housing. If the heater malfunctions or needs service, you want a disconnecting means that doesn't require you to disassemble the heater to kill the power.


Accessibility

Kick space heaters are often in... well, kick spaces. Bending over and reaching under a cabinet to find a small switch isn't "readily accessible" in the way the NEC intends.

Therefore, you likely need to install a separate disconnecting means.
2. Acceptable Disconnecting Means Options Switch

A dedicated switch is the most common and generally preferred method.

Location

Locate the switch within sight of the kick space heater and readily accessible. This usually means mounting it on the wall near the cabinet housing the heater. Check your local codes for specific height requirements for switch installations (typically between 15" to 48" from the floor).


Type

A standard single-pole switch, rated for the voltage and amperage of the heater, is usually sufficient.

Circuit Breaker Lockout

In some limited circumstances (consult your local inspector!), you
might be able to use a circuit breaker lockout device at the panel as the disconnecting means. However, this is rarely the preferred method for appliances and is much less convenient. The breaker must be lockable and clearly labeled.

3. Wiring with Romex (NM Cable)
General Rule

You can generally use NM cable (Romex) to wire a kick space heater. However, there are some important considerations:

Dry Location

NM cable is only approved for dry, indoor locations. Make sure the area where the heater is installed is considered a dry location. Kitchens can be damp, so ensure the wiring is not exposed to excessive moisture.


Protection

Where the NM cable is exposed and subject to physical damage (e.g., near the floor, running through a cabinet), you'll need to protect it with conduit (EMT or PVC).

Strain Relief

Where the NM cable enters the heater's junction box, you
must use a proper strain relief fitting (a cable clamp). This prevents the wires from being pulled loose from the connections inside the heater.

Connecting to the Heater



Junction Box

The kick space heater should have a built-in junction box (or a designated area for wiring connections). This is where you'll make your electrical connections.


Wire Connectors

Use appropriate wire connectors (wire nuts or push-in connectors) to make secure connections between the NM cable conductors and the heater's wires. Follow the heater manufacturer's instructions.

Grounding

Ensure that the heater is properly grounded. Connect the grounding conductor (bare or green wire) from the NM cable to the grounding screw inside the heater's junction box.

Important Considerations and Best Practices



Local Codes

Always consult and follow your local electrical codes. Local codes can be more stringent than the NEC. Your local building department is the final authority.

Heater Manufacturer's Instructions

Carefully read and follow the heater manufacturer's installation instructions. They may have specific wiring requirements or recommendations.


Amperage

Determine the heater's amperage rating (usually found on a nameplate on the heater). Use wire of the correct gauge for that amperage and a circuit breaker of the correct size. Overloading the circuit is a fire hazard.

Professional Installation

If you are not comfortable working with electrical wiring, hire a qualified electrician. Electrical work can be dangerous, and incorrect wiring can lead to fires or shocks.


GFCI Protection

Depending on your local codes and the location of the heater (e.g., near sinks), you might be required to provide GFCI (Ground Fault Circuit Interrupter) protection for the circuit.

In Summary


Install a separate disconnecting switch
within sight of the kick space heater.2. You can likely use NM cable (Romex), but make sure it's protected from physical damage and properly secured.3. Follow all applicable codes and manufacturer's instructions.4. When in doubt, consult a qualified electrician. Flag for review

Previous Question Next Question