Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Neutral and ground in same panelboard

User: sparkync, Location: North Carolina

Asked on: Monday, November 4, 2024 at 6:28 am EST
Answered on: Thursday, March 6, 2025 at 4:47 am EST

Question: I have a "Main panel" with a sub panel directly beside it. I'm having to move a "240 volt" dryer circuit out of the "Main panel" into the sub panel in order to make room for a "generator main breaker" at the top of the panel near the 200 amp "Main breaker" for the "inter-lock" kit. By code does the neutral and equipment ground wire, have to be moved also? The Main panel is very "congested" with wires, making it hard to "access" the neutral and ground wire. I know the circuit will work of course, bur what does the Code say about it. Thanks

Okay, let's break down the code requirements for moving that dryer circuit, focusing on the neutral and ground.

The Short Answer (Generally)

Yes, you must move both the neutral and ground wires along with the hot wires when moving a 240V circuit from a main panel to a subpanel.

The Reasoning (and Code References)



Subpanel Wiring Configuration (NEC Article 250)

This is the core of the issue. In a subpanel, the neutral (grounded conductor) and the equipment grounding conductor (ground wire)
must be kept separate. They should never be bonded together in the subpanel. The only place they are bonded is at the main panel.

Why Separate?
This separation is critical for safety. If the neutral and ground are bonded in the subpanel, you create parallel paths for neutral current. This means some of the neutral current could flow through the ground wire. This is dangerous for several reasons: Electromagnetic Interference (EMI)

Current flowing through the ground wire can induce EMI in nearby electronic equipment.


Nuisance Tripping

Even small amounts of current on the ground wire can cause GFCI (Ground Fault Circuit Interrupter) breakers to trip unnecessarily.

Shock Hazard

If there's a fault in the neutral, it could energize the ground wire, creating a shock hazard.


Dryer Circuit Specifics (NEC Article 250.140)

Although a dryer circuit is 240V, it also includes a neutral wire for the 120V components of the dryer (e.g., the timer, light). Therefore, it's not just a straight 2-pole circuit. It is a 120/240V circuit.

Relocating the Circuit

When you move the entire circuit to the subpanel, it becomes part of the subpanel's wiring system. Therefore, the subpanel's rules regarding neutral and ground separation
must be followed.

In your specific situation


You are moving the 240V dryer circuit from a main panel to a subpanel.
This change in location triggers the requirement for separate neutral and ground in the subpanel.2. The "congested" wiring

I understand that accessing the neutral and ground connections in the main panel is difficult. However, this doesn't excuse you from following the code. Carefully and safely work to gain access to those wires. You may need to temporarily disconnect other circuits (always de-energize before working!), carefully label them, and move them out of the way to create working space. You may also be able to re-route or shorten some existing wires to free up space.

What to do in the Subpanel


Neutral Bar

Connect the dryer circuit's neutral wire to the neutral bar in the subpanel. Make sure the neutral bar is
isolated from the subpanel enclosure.2.

Ground Bar

Connect the dryer circuit's ground wire to the ground bar in the subpanel. The ground bar
must be bonded to the subpanel enclosure.

Important Considerations



Local Codes

Always check with your local electrical inspector. Local codes may have additional requirements or interpretations that differ slightly from the NEC.

Safety First

Electricity is dangerous. If you are not completely comfortable and knowledgeable about electrical work, hire a qualified electrician.


Permits

Depending on your location, you may need a permit for this type of work.

In summary, while it might be tempting to leave the neutral and ground wires in the main panel due to the difficulty of access, it's a code violation and a safety hazard. You must move all conductors of the circuit, including the neutral and ground, to the subpanel, ensuring proper separation of neutral and ground as required by code.
Flag for review

Previous Question Next Question