Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: over 2000' LONG distance pipe run in the ground

User: Ken Forest, Location: Knoxville

Asked on: Monday, November 4, 2024 at 3:56 pm EST
Answered on: Thursday, March 6, 2025 at 4:49 am EST

Question: I am figuring out some general rule on long distance/large size underground wire/pipe run.the wire size is 250 MCM in 4" conduits but the distance is over 2000' with zigzaging with 90 five times.I understand the need of pull boxes and basic requirements of them along the way. but Trying to minimize without making the work too hard is my challenge.the pull rope we normally use is 350'. Thinking logically, I would need to set boxes in the ground within 350' all the way.Do you have any other suggestions? Finding/using a longer rope makes the work easier/harder? Are there some common knowledge that I am not familiar with when installing this long distance wire/pipe?Appreciate your input!k.m.

You're right to be concerned about the complexities of pulling 250 MCM cable through 4" conduit over 2000 feet with multiple 90-degree bends. That's a significant pull! Here's a breakdown of things to consider and some suggestions to minimize pull points while still ensuring a safe and efficient installation

Key Considerations & Challenges:
Pulling Tension

This is the most critical factor. Exceeding the maximum pulling tension of the conductor can damage the insulation and reduce its lifespan. 250 MCM conductors have a specific pulling tension rating (check the manufacturer's data sheets). The more bends and the longer the run, the higher the pulling tension.


Sidewall Pressure

Bends create sidewall pressure on the cable. This pressure, especially at 90-degree bends, can also damage the insulation. Sidewall pressure is most critical on larger conductors like 250 MCM.

Coefficient of Friction

The friction between the cable and the conduit walls increases with the length of the run and the number of bends. Different types of conduit and cable jackets have different coefficients of friction. PVC generally has lower friction than rigid metal conduit.


Conduit Fill

While 4" conduit seems spacious, the cumulative effect of multiple 250 MCM conductors and the lubricant can make pulling difficult if the fill percentage is too high.

Cable Lubricant

Essential for reducing friction. Use a high-quality, specifically formulated cable lubricant compatible with the cable jacket and conduit material. Apply it generously.


Conduit Bends

Five 90-degree bends over 2000 feet is a lot. Code (NEC) has limits on the total degrees of bend allowed between pull points, typically 360 degrees. You're already exceeding that significantly.

Pulling Rope Strength & Reliability

The rope needs to be strong enough to handle the anticipated pulling tension with a substantial safety factor. It also needs to be durable and resistant to abrasion.


Crew Communication

Clear and reliable communication between the pulling and feeding ends is crucial for a safe and successful pull.

Obstacles & Changes in Elevation

The actual route may have unforeseen obstacles or changes in elevation that affect the pull.

Suggestions and Best Practices

1.

Professional Pulling Tension Calculations are MANDATORY

Before you even start, get a professional pulling tension calculation performed. There are software programs specifically designed for this (e.g., AccuBend, Pull-Planner). These programs will consider the cable type, conduit type, number of bends, bend radii, conduit length, and lubricant to estimate the pulling tension and sidewall pressure. This will tell you definitively whether your proposed plan is feasible. This is the most important advice I can offer.2.

Optimize the Conduit Route



Minimize Bends

The most effective way to reduce pulling tension is to reduce the number of bends. Can you adjust the route slightly to reduce the number of 90-degree bends? Consider using shallower bends (e.g., 45-degree bends) to achieve the necessary directional changes. Each bend adds significantly to the pulling tension.

Increase Bend Radius

Larger radius bends reduce sidewall pressure and pulling tension. Use the largest bend radius practical.


Direct Burials (if possible and permissible)

If regulations and soil conditions allow, consider direct burial cable instead of conduit in certain sections. This eliminates the friction of the conduit. You would still need conduit for protection where the cable enters/exits buildings or crosses roadways.3.

Strategically Placed Pull Points (Vaults or Handholes)



Placement Based on Calculations

Use the pulling tension calculations to determine the
optimal placement of pull points. The goal is to keep the pulling tension and sidewall pressure below the manufacturer's limits at each pull point.

Staggered Pull Points

Don't put pull boxes right after a bend. Allow a straight section of conduit after a bend before the next pull box to allow the cable to relax and reduce sidewall pressure.

Consider Vaults vs. Handholes

For such a long run with potentially high pulling forces, consider using larger vaults instead of smaller handholes. Vaults provide more room for workers and equipment to manage the cable and reduce the pulling force.4.

Cable Selection



Low-Friction Cable Jacket

Consider using a cable with a low-friction jacket designed for long pulls. These cables have a special coating that reduces the coefficient of friction.

Compact Conductor Stranding

More compact stranding can make the cable more flexible and easier to pull.5.

Pulling Equipment & Techniques



Powered Puller

A powered cable puller is essential for a pull of this magnitude. Choose a puller with a tension monitor and automatic shut-off to prevent over-tensioning the cable. Calibrate the puller before use.

Cable Feeder

A cable feeder helps to control the cable being fed into the conduit and prevents it from bunching up or getting tangled.


Head Snout

A pulling head snout guides the cable into the conduit and helps to prevent damage.

Mid-Assist Pulling

If possible, consider using mid-assist pulling. This involves placing a pulling machine at an intermediate pull point to reduce the length of the individual pulls.


Backfeeding

Sometimes, it's easier to "backfeed" the cable into the conduit than to pull it. This involves pushing the cable into the conduit from one end while simultaneously pulling it from the other.6.

Longer Pull Rope and Alternatives



Longer Rope (Dyneema or Similar)

A longer, stronger pull rope is generally beneficial. Consider using a high-strength synthetic rope like Dyneema (Spectra). It's significantly stronger and lighter than traditional ropes, reducing the risk of rope breakage. A longer rope also allows you to position the pulling equipment farther away from the pull point, which can be helpful in tight spaces. Be sure to use a swivel on the pull head to prevent the rope from twisting.


Rope Lubrication

Lubricate the pull rope itself to reduce friction between the rope and the conduit.

Consider a "Pulling Snake" or "Mandrel"

For very long and difficult pulls, a pulling snake (or mandrel) can be used. This is a flexible, steel cable that is pushed or pulled through the conduit first. The pulling rope is then attached to the snake, which is used to pull the rope through the conduit. This can help to overcome obstacles and reduce friction.7.

Lubrication is KEY!
Apply Lubricant Generously

Don't skimp on the lubricant! Use a generous amount of high-quality cable lubricant specifically designed for electrical cable pulling.

Lubricate Continuously

As the cable is being pulled, continuously apply lubricant to the cable as it enters the conduit.


Use the Correct Lubricant

Make sure the lubricant is compatible with the cable jacket and conduit material. Some lubricants can damage certain types of cable jackets.8.

Communication is Critical



Two-Way Radios

Use two-way radios for clear communication between the pulling and feeding ends.


Pre-Pull Briefing

Conduct a pre-pull briefing to discuss the pulling plan, potential hazards, and emergency procedures.

Stop Signals

Establish clear stop signals to halt the pull immediately if problems arise.9.

Documentation



Record Pulling Tension

Carefully record the pulling tension at each pull point. This information is valuable for future reference and troubleshooting.

Document Conduit Route

Keep a detailed record of the conduit route, including the location of all pull points, bends, and any other significant features.

Common Knowledge You Might Be Missing



NEC (National Electrical Code)

While you mentioned you know about the basics, the NEC has specific requirements regarding conductor fill, conduit bending radius, and the number of bends allowed between pull points. Ensure you are compliant with all applicable NEC requirements and local codes.

Conductor Derating

Long runs can result in voltage drop. You might need to increase the conductor size to compensate for voltage drop, especially if the load is sensitive to voltage fluctuations. Perform voltage drop calculations.


Grounding & Bonding

Proper grounding and bonding are crucial for safety. Ensure that the grounding and bonding conductors are properly sized and installed.*

Experience

This type of long, complex pull is best handled by experienced electricians and pulling crews. If you don't have the necessary experience in-house, consider hiring a specialized contractor.

In summary:
A 2000-foot pull with five 90-degree bends is a complex undertaking that requires careful planning, the right equipment, and experienced personnel. Prioritize getting professional pulling tension calculations, optimizing the conduit route, and using high-quality materials and techniques. Don't underestimate the importance of lubrication and communication. Good luck! Flag for review

Previous Question Next Question