User: Dansos, Location: PA
Asked on: Tuesday, November 5, 2024 at 7:20 am EST
Answered on: Thursday, March 6, 2025 at 4:50 am EST
Question: Good morning All!!I’m getting ready to install a 3 pos (200A ea) meter stack and we’re trying to figure out feeder size. (Meters will be for Unit 1, Unit 2 and LL)Im planning to run 400AL x 2 for feeders.(Used table 312.10 to figure out)IF I was to use Art 220 and do a load calc, would THOSE figures be used to size the feeders using 312.10?I guess I’m just asking if a load calculation would OVER RULE everything else and we’ll be allowed to run whatever size wire we calculate or is there something I’m missing here?Just an FYI, the land lord panel will only be used for a camera system and a space heater in the basement. No common lighting (other than basement) BUT I understand that our calcs will only be applicable to this current situation and someone may come in the future all load stuff up. Is that something to worry about (from a code perspective) or do we not worry about future stuff like that?
Good morning! Let's break this down, and I'll address your concerns about load calculations and future-proofing.
Understanding the Basics Meter Stack
A meter stack is a consolidated panel containing individual meters for multiple dwelling units and/or common areas.
Feeders
The conductors that bring power from the service equipment (main panel or transformer) to the meter stack.
Load Calculation (Article 220)
Estimating the anticipated electrical demand of each unit and common areas.
310.16 vs 310.15(B)(7) & 230.42(B)
You're using Table 310.16, which dictates the ampacity of conductors based on insulation type and ambient temperature.
Addressing Your Questions1. Load Calculations Override Wire Size? YES, but with conditions. A proper load calculation (Article 220) is the foundation for determining the minimum required ampacity for your feeders. Code Compliance is Key
Your feeder conductors must have an ampacity equal to or greater than the calculated load. This is the primary requirement.
310.15(B)(7) (formerly 310.15(B)(7)
If the installation is a service or feeder for an entire dwelling unit, that can use the reduced ampacities per 310.15(B)(7). This would allow smaller wire.
230.42(B)
Similar to 310.15(B)(7) but for the service entrance conductors only. Protection Requirements
You still must consider the OCPD rules in 240.4.
2.
Sizing Your Feeders (Your Plan) 400 kcmil Aluminum x 2 per phase
Based on Table 310.16. 400kcmil AL at 75C is typically rated for 300 Amps per conductor. Two in parallel will be 600 Ampere total.
Important Note
You need to look at 110.14(C). Most terminations are only rated for 75 degrees C.
3.
Load Calculation and Landlord Panel Your Approach is Correct
Calculate the load for each unit (Article 220, Part III) and the common area (landlord panel) (Article 220, Part IV). Add them up.
Landlord Panel
You're right to include the camera system and space heater.
NEC 220.87 - Optional Feeder or Service Load Calculations for Existing Installations If it's an existing building, you can use that formula (220.87) and use the previous 12 months of utility data.
4. Future Loads – The "What If" Scenario Code Focus
The NEC only requires you to size your feeders and service to handle the present calculated load. You're not strictly obligated to plan for unspecified future increases.
Practical Considerations
Oversizing (Within Reason)
It's often prudent to slightly oversize the feeders, within budget and equipment limitations, to provide headroom for future expansion. This is especially true if you anticipate significant changes (e.g., tenants known to use a lot of power).
Consult the Landlord
Discuss potential future uses with the property owner. This can help inform your decision.
Documentation
Document your load calculations and the rationale behind your feeder sizing. This protects you later if loads increase.
Example (Simplified)
Let's say: Unit 1 Calculated Load: 100 Amps Unit 2 Calculated Load: 120 Amps Landlord Panel Calculated Load: 30 Amps Total Calculated Load: 250 AmpsIn this case, your feeders need to have an ampacity of at least 250 Amps.
Important Considerations Conduit Fill
Make sure your conduit is properly sized for the number and size of conductors you're using.
Voltage Drop
Check voltage drop. Excessive voltage drop can damage equipment.
Local Codes and Regulations
Always verify and comply with all local electrical codes and regulations.
Coordination
Coordinate with the utility company regarding their requirements for meter sockets and service equipment.
Professional Inspection
Have your work inspected by a qualified electrical inspector.
Recommendation1. Perform a Detailed Load Calculation
This is the most important step. Article 220 is your guide.2.
Determine Feeder Ampacity
Based on your load calculation.3.
Select Conductors
Choose conductors with the appropriate ampacity, insulation type, and size, using Table 310.16 and considering termination temperature limitations.4.
Consider Oversizing
If practical and budget allows, consider slightly oversizing for future flexibility.5.
Document Everything
Keep thorough records of your calculations and decisions.
Disclaimer: Consult with a licensed and qualified electrician for your specific project. Flag for review