Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Adding a main Breaker

User: Tdubya90, Location: Denver

Asked on: Tuesday, November 5, 2024 at 5:43 pm EST
Answered on: Thursday, March 6, 2025 at 4:52 am EST

Question: Hello, does anyone know if there is a code that states that the main breaker has to be bolted to the can? I have a customer that has an old panel with no main shut off. Wondering if there's any reason not to just pop a 100 amp breaker to the bus and re-route the feeders to that breaker? Thanks

Okay, let's break down the situation and the code implications. You're dealing with an older panel without a main breaker and considering adding a 100A breaker as a main disconnect.1. The Bolted Connection Question NEC doesn't explicitly require bolting the main breaker to the can itself. The primary requirement is that the breaker be securely fastened within the panelboard enclosure. This usually means it's properly clipped or bolted onto the bus bars and secured by the panelboard's deadfront (cover). Some manufacturers use bolts for larger breakers to ensure good electrical connection to the bus bar. These are more common on breakers 200A and above.2. Adding a Breaker as a Main Disconnect - Considerations Listing and Suitability

The biggest potential issue is whether the panelboard is
listed and labeled for use with a breaker as a main disconnect and if that breaker is the correct type for that panelboard. Older panels, especially those designed without a main breaker, may not have been evaluated for that purpose. You

must
verify the panelboard is compatible with the breaker you intend to use. Look for markings on the panel itself. Interrupting Rating

The interrupting rating (AIC - Ampere Interrupting Capacity) of the breaker must be sufficient for the available fault current at the service location. This is a critical safety factor. You need to know what the available fault current is at the service entrance. Contact the local utility to inquire about the available fault current at your location.

Panelboard Rating

Make sure the panelboard's ampacity rating is adequate for the load served and is at least the size of the new breaker you are installing.


Working Space

You must have adequate working clearance in front of the panelboard according to NEC 110.26.

Six Disconnect Rule (Generally NOT Applicable Here)

NEC 230.71(A) allows up to six switches or circuit breakers to serve as the service disconnecting means for each service.
However, this usually only applies if you're installing a completely new service. In your case, you're trying to add a single main disconnect to an existing panel.

Neutral and Grounding

Ensure the neutral and grounding connections are correct and compliant with current NEC requirements (typically, neutral and ground are bonded at the service entrance, but not at subpanels).

Overcurrent Protection

Make sure the overcurrent protection is adequate for the size of the conductors that are feeding the panel.

3. Code Sections to Review
NEC 110.3(B)

Equipment shall be installed and used in accordance with its listing and labeling.

NEC 110.9

Interrupting Rating


NEC 110.14(C)

Electrical Connections - requires that terminations and splicing devices be identified for the material of the conductors.

NEC 110.26

Working Space about Electrical Equipment


NEC Article 230

Services (especially parts related to disconnecting means and overcurrent protection).

NEC 408

Switchboards and Panelboards. Pay close attention to requirements for overcurrent protection and identification.

4. Important Warnings and Recommendations
THIS IS NOT A SIMPLE DIY PROJECT. Working on electrical panels is dangerous and potentially deadly. It requires expertise in electrical theory, code compliance, and safe work practices. Consult a Qualified Electrician

You absolutely need to consult with a licensed and experienced electrician before proceeding. They can assess the panel's condition, determine if it's suitable for this modification, ensure the breaker is compatible, verify the AIC rating, and perform the work safely and correctly.


Permitting and Inspection

Check with your local permitting authority about the need for a permit and inspection. This is usually required for any work on a service panel.

Replacement Might Be Better

Depending on the age and condition of the panel, it might be more cost-effective and safer to replace the entire panel with a new one that has a built-in main breaker. A new panel will likely be safer, more efficient, and provide more circuit capacity.

In summary

While adding a breaker as a main disconnect
might* be possible, it's not a straightforward swap. The suitability of the panel and the correct selection of the breaker are critical.

Do not proceed without consulting a qualified electrician and obtaining the necessary permits.
Replacing the entire panel is often the better long-term solution. Flag for review

Previous Question Next Question