Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Ground fault 4000 amp GE power Break 1, Manual type

User: Fordean, Location: New Jersey

Asked on: Thursday, November 7, 2024 at 11:49 am EST
Answered on: Thursday, March 6, 2025 at 4:56 am EST

Question: Had a call on a 4000 amp Main breaker. It has tripped 2 times. This past tuesday. and 6 months ago.Happened at 200 am, They company employees Tried to Reset breaker. But after charge, Would not close, And remained open. And 3 attempts 2 hr later,It finally reset.I viewed the screen on the Microversa Trip plus trip unit. And it looks to have a error code displayed, .23 I believe GF code, Which is ground fault. Any input,They want to remove this breaker. And replaced.GE TP4040TR Power break 1 type.4000 amp CT Chip in Micro switchMicroversa Trip plus trip unit

Okay, let's break down this situation. You've got a 4000A GE Power Break 1 breaker tripping intermittently with a ground fault indication on the Microversa Trip Plus. Here's how I would approach this

Understanding the Situation
Intermittent Tripping

This is a problem because it suggests the fault condition isn't constant. It could be influenced by load, temperature, or transient events.


Tripping at 2:00 AM

While not a certainty, this could point to something load-related changing. Consider what equipment might be cycling on or off at that time. Also, outside electrical events are more common overnight.

Failure to Reset Immediately

This is a key symptom. The breaker's inability to immediately reset after a trip, followed by a successful reset later, suggests a lingering condition. This could be a fault that eventually clears itself, a component overheating and then cooling, or a control issue that has a time component.


Error Code .23 (Ground Fault)

This strongly suggests a ground fault condition. It doesn't guarantee a ground fault in the load, but it does mean the trip unit believes there's one.

Investigation Steps Before Replacement
Verify the Trip Unit Settings



Ground Fault Protection Settings (GF Pickup and Delay)

Critically important. Look at the trip unit settings. What is the ground fault pickup current (in amps)? What is the ground fault delay time? Is the pickup current setting appropriate for the system? Is the delay setting providing adequate coordination with downstream devices? Someone could have accidentally changed these settings, making it overly sensitive. Record the existing settings before making any changes.

Testing the Ground Fault Circuit

Check the continuity between the ground and other lines with a multimeter.


Review the One-Line Diagram

Understand the entire electrical distribution system. Where does this 4000A breaker feed? What are the downstream loads? This is essential for understanding potential fault locations.

Check Grounding System Integrity



Main Bonding Jumper (MBJ)

Verify the size and integrity of the main bonding jumper connecting the neutral to the ground at the service entrance. A loose or corroded MBJ can create ground fault issues.


Grounding Electrode System

Inspect the grounding electrodes (ground rods, water pipe ground, etc.) and their connections. Ensure they are intact and not corroded. Measure the ground resistance if possible.

Visual Inspection of the Breaker and Buswork



Breaker Condition

Look for any signs of overheating, arcing, or physical damage on the breaker itself. Check for loose connections, especially on the CT connections to the trip unit.

Buswork

Inspect the buswork connected to the breaker. Look for signs of corrosion, overheating, or insulation damage.


Insulation Resistance Testing (Megger)

This is crucial. With the breaker OFF and locked out/tagged out, perform insulation resistance testing (meggering) on the feeder cables connected to the breaker and on the load-side conductors. Test each phase-to-ground and phase-to-phase. Record the megger readings. Low insulation resistance indicates insulation breakdown and a potential ground fault.

CT Inspection and Testing



CT Connections

Carefully inspect the CT connections to the trip unit. Ensure they are clean, tight, and properly wired.

CT Ratios

Verify the CT ratios are correct for the system.


CT Testing

If possible, perform CT ratio and polarity testing to confirm the CTs are functioning properly. A faulty CT can cause false ground fault trips.

Power Quality Monitoring

Install a power quality monitor at the breaker to record voltage, current, harmonics, and transient events. This can help identify the source of the ground fault, especially if it's intermittent.

Check Neutral to Ground Voltage

Measure the voltage between neutral and ground at the main service entrance. Excessive voltage (more than a few volts) can indicate grounding problems or excessive neutral current.


Review Recent Electrical Work

Has any electrical work been done recently on the system fed by this breaker? New equipment installations or modifications can sometimes introduce ground fault problems.

Trip Unit Self-Test

Consult the trip unit's manual for specific instructions on how to perform a self-test. This test can verify the functionality of the trip unit's internal circuitry.

Why This is Important Before Replacement



Replacing the breaker without finding the root cause is risky.
If the problem is downstream, the new breaker will likely trip as well. You'll be spending money and time without fixing the issue. The old breaker may not be faulty. The trip unit is doing its job by detecting a ground fault condition. The problem is what's causing the ground fault. A thorough investigation provides valuable information. Even if you end up replacing the breaker, the data you collect during the investigation can help prevent future problems.

When to Consider Replacement (After Investigation)



The breaker itself is damaged.
If you find signs of arcing, overheating, or physical damage on the breaker, replacement is necessary. The trip unit is faulty. If the trip unit self-test fails, or if you suspect the trip unit is malfunctioning after thorough testing, replacement may be necessary. The breaker is nearing its end of life. Power breakers have a limited lifespan. If the breaker is very old and has seen a lot of use, it might be prudent to replace it proactively. Parts are unavailable. If parts for the existing breaker are difficult or impossible to obtain, replacement may be the only option.

Before Replacing



Order the Correct Replacement

Ensure the replacement breaker has the same frame size, interrupting rating, voltage rating, and trip unit functionality as the existing breaker.

Coordination Study

Perform a coordination study to ensure the replacement breaker is properly coordinated with the downstream protective devices.


Plan for Downtime

Replacing a 4000A breaker will require a significant outage. Plan the outage carefully to minimize disruption to the facility's operations.

Important Safety Considerations



Lockout/Tagout

Always follow proper lockout/tagout procedures before working on any electrical equipment.


Qualified Personnel

Only qualified electricians should perform the investigation, testing, and replacement of the breaker.

Personal Protective Equipment (PPE)

Wear appropriate PPE, including arc-rated clothing, safety glasses, and gloves.


Arc Flash Hazard

Be aware of the potential arc flash hazard and take appropriate precautions.

In summary, focus on thorough investigation first.
The error code strongly suggests a ground fault condition. Pinpointing the source of that ground fault is the key. Only after eliminating other possibilities should you consider replacing the breaker. Document everything you do. Flag for review

Previous Question Next Question