User: W@ttson, Location: USA
Asked on: Thursday, November 7, 2024 at 3:41 pm EST
Answered on: Thursday, March 6, 2025 at 4:57 am EST
Question: Suppose I have a motor that when ran at 60HZ its full load current is 100A. The motor is fed by a flux vector drive. The load is a constant torque load.The input to the drive would be something on the order of Iout x Drive input PF. Say the input to the drive had a pf of 0.95, then the current input to the drive is 95A.The drive makes up 98% of the load in the distribution system. So I assume that the current at the service will be more or less 100A, factoring in some current for some other misc loads.Now suppose I run that motor at a maximum Hz of 30hz. This being a constant torque load my torque will be the same so my torque producing current will be the same. I assume my magnetizing current will change a bit due to the change in impedances at the lower frequency. My overall current should be more or less 100A at the output. Perhaps a little higher since my inductance will be slightly higher.Again I assume that my input to my drive would be around 0.95 of the output current and I should assume that my service current largely stays the same.Am I getting all of the above correct?
Let's break down your reasoning and see if it holds true.
Understanding the Motor and Load Constant Torque Load
This means the motor needs to produce the same torque regardless of speed. This is crucial because torque is directly related to current in a motor (especially the torque-producing component).
Flux Vector Drive (Vector Control)
This type of drive precisely controls both the magnitude and phase of the motor current, allowing for good torque control even at lower speeds. It attempts to maintain a constant air gap flux.
Analyzing Your Assumptions1. Motor at 60 Hz (Base Case)
Full Load Current (FLA) = 100A Drive Input Power Factor (PF) = 0.95 Drive Input Current = FLA / PF = 100A / 0.95 = ~105.26A
NOT 95A The drive represents 98% of the load. Service Current (assuming other small loads) ≈ ~105.26A2. Motor at 30 Hz
Constant Torque Requirement
This is the key. The motor must still provide the same torque.
Torque-Producing Current
This component of the current must remain relatively constant to maintain the torque.
Magnetizing Current
This is where things get trickier. At lower frequencies, the inductive reactance (X_L = 2πfL) of the motor windings decreases. To maintain constant flux in a flux vector drive, the voltage must be reduced proportionally to the frequency. Ideally, the drive tries to maintain a constant Volts/Hertz (V/Hz) ratio. Lowering the voltage and frequency keeps the magnetizing current more or less constant. However, it's not perfectly constant in the real world, and the drive will adjust.
Overall Motor Current
At 30 Hz, the drive will reduce the voltage while keeping the current close to 100A. The exact value depends on the drive's control strategy and any losses in the motor. You are right that the magnetizing current will be different but in a good drive it will be close to the 60hz current to keep the flux constant.
Drive Input Current
This is where your assumption is the most critical. It is incorrect to assume that the input current will be around 0.95 of the output current. Your current will depend on the drive's efficiency and the power factor. The input to your drive is in KVA(Apparent Power)3.
Service Current
This is the most questionable part of your analysis. You cannot assume the service current stays largely the same. Here's why: Power Factor at 30 Hz
The power factor of the motor and the drive will change at 30 Hz compared to 60 Hz. Lower frequency can sometimes lead to a worse (lower) power factor, even with a good vector drive. The impact of this can be calculated as:
Power In= Power Out/ Efficiency: Power Out = Torque Speed: This means power out is halfed by the speed reduction, and the motor output current is kept constant. The input current must decrease!Corrections and Key Considerations1. Power Factor Correction
The drive's input power factor is critical. While a drive attempts to maintain a good power factor on the input, it's not always perfect, especially as you move away from the design frequency.2.
Drive Efficiency
The drive itself has losses. These losses are converted into heat. Lowering the speed will lead to slightly lower losses, which is important but not by a major amount.3.
Volts/Hertz Control
The drive attempts to maintain a constant Volts/Hertz ratio. This is essential for preventing saturation of the motor's magnetic core.4.
Harmonic Distortion
Drives generate harmonic currents on both the input and output sides. Lower frequencies can sometimes exacerbate harmonic problems. This can affect the overall current draw at the service.5.
KVA Demand
Focusing on KVA (kilovolt-amperes, apparent power) is more accurate than just looking at current. KVA takes both voltage and current (and phase angle) into account.
Revised Analysis
Here's how you should approach the 30 Hz scenario:1. Determine the Output Power
Since torque is constant, and speed is halved (30 Hz vs. 60 Hz), the output power of the motor is halved.2.
Estimate Input Power
Input Power = Output Power / Drive Efficiency. The drive's efficiency might change slightly at lower speeds, so refer to the drive's datasheet.3.
Measure Input Current
Measure the input current to the drive with a clamp meter! This is the only way to know for sure.4.
Calculate Input KVA
KVA = (Volts Amps) / 1000 (assuming you're working with kilovolts).5.
Consider Other Loads
Add the KVA of your other loads.6.
Determine Service Current
Calculate the service current based on the total KVA and the service voltage.
In Summary
Your fundamental understanding of constant torque loads and flux vector drives is good. However, the assumption that the service current stays the same at 30 Hz is highly unlikely and incorrect. Power factor, drive efficiency, and the reduction in output power all play a significant role. Always measure the actual current draw to confirm your calculations. Flag for review