Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Failed Inspection

User: dsarvis000, Location: Virginia

Asked on: Thursday, November 7, 2024 at 7:01 pm EST
Answered on: Thursday, March 6, 2025 at 4:58 am EST

Question: I failed an inspection today bc I landed my wire for the water bonding in a lug that I installed into my main panel (bonded) and not into the actual neutral/ground bars installed on the panel.The reason I was given was bc the water system was coming from underground and was metallic turning into an electrode and not a simple bondMy question is one is this correct, two if so where in the code does it say this, and three what’s the difference if the panel is bonded ?

Okay, this is a common point of confusion. Let's break down the reasoning and code references.1. Is the Inspector's Reasoning Correct? Yes, most likely. The inspector is distinguishing between a bonding connection and a grounding electrode conductor (GEC) connection. The water pipe system, especially when entering the building underground, is always considered a grounding electrode. Your statement about installing the lug on a bonded portion of the panel is the source of the misunderstanding. A bonded portion of the panel is still the enclosure of the panel, and an enclosure connection is generally for equipment grounding conductors. Equipment grounds (like the ground wire in a cable running to an outlet) are different than grounding electrodes. The reason this is happening is because your water main becomes a grounding electrode.2. Code References (NEC - National Electrical Code)

The relevant sections are primarily within

Article 250 (Grounding and Bonding)
, particularly: 250.64(A): Grounding Electrode Conductor Installation. _"Grounding electrode conductors shall be installed in one continuous length without a splice or joint, unless spliced only by irreversible compression-type connectors listed for the purpose or by the exothermic welding process."_ This reinforces the need for a dedicated, reliable path. 250.52(A)(1): Metal Underground Water Pipe. _"A metal underground water pipe in direct contact with the earth for 10 ft. (3.0 m) or more (including any metal well casing bonded to the pipe) and electrically continuous to the points of connection of the grounding electrode conductor and the bonding jumpers shall be considered a grounding electrode. Continuity of the grounding path or the bonding connection to interior piping shall not rely on water meters or filtering devices and similar equipment. The interior metal water piping system shall be bonded to the grounding electrode system as required by 250.
104."_ This defines the water pipe as a grounding electrode. 250.24(A): Grounding Service-Supplied Alternating-Current Systems. This section generally outlines how service conductors, neutral, and grounding electrodes are connected. Pay particular attention to the requirement of connecting the GEC to the neutral conductor at the service equipment.3. Why Can't I Just Use a Lug on a Bonded Part of the Panel? (Difference even if the Panel is Bonded)

Here's the crux of the issue:
Different Purpose

Equipment grounding conductors (EGCs) and grounding electrode conductors (GECs) serve different functions.

Equipment Grounding (Bonding)

EGCs (the ground wires in your circuits) are intended to provide a low-impedance path
back to the source (transformer) to facilitate the operation of overcurrent devices (breakers/fuses) in case of a fault. They connect to the metal enclosures of equipment and are bonded to the panel enclosure.

Grounding Electrode System

GECs connect to the earth (through electrodes like water pipes, ground rods, etc.). Their primary purpose is to stabilize voltage to earth and limit voltage surges (like from lightning). They provide a path to dissipate fault current into the earth if needed.

Dedicated Connection

The GEC
must have a direct, reliable connection to the neutral bus/grounding bus in the service panel. This is to ensure that the grounding electrode system is properly connected to the neutral and the service. A lug bolted to the panel enclosure, while electrically bonded, is not considered equivalent to a direct connection to the neutral/grounding bus.

Potential for High Current

During a fault, the grounding electrode conductor could carry a substantial amount of current. The connection to the neutral/ground bus is designed to handle that. A connection to the enclosure, even if bonded, might not be rated or designed for that level of fault current.

Listing and Suitability

The neutral/ground bars are specifically listed and designed for accepting grounding electrode conductors. The enclosure is not.

In Summary (Practical Application)


The GEC (from your water pipe) needs to terminate directly on the neutral/ground bar in your main panel.
2. You'll likely need to remove the wire from the lug you installed and connect it to one of the terminals on the neutral/ground bar. You may need to add another grounding bar if you are out of space on the exisiting one.
3. Make sure the connection is tight and secure.4. If your water meter is insulated or uses plastic fittings, you may need to bond around it with a bonding jumper.

Important Considerations



Local Amendments

Always check for local amendments to the NEC in your jurisdiction. Some areas have specific requirements for grounding and bonding.

Inspection Authority

The inspector's interpretation is what matters. If you have a good relationship, ask for further clarification and specific code references he's relying on.


Professional Advice

If you're unsure, consult with a licensed electrician. Grounding and bonding are critical for safety.*

Supplementary Electrode:
It's best practice to always supplement a metal water pipe electrode with an additional electrode, such as a ground rod or ground ring. This ensures a reliable grounding system, even if the water pipe is replaced with non-metallic materials in the future.By following the code and understanding the different roles of grounding and bonding conductors, you can ensure a safe and compliant electrical installation. Flag for review

Previous Question Next Question