Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: 312.5 C would this apply to bare GEC ?

User: acrwc10, Location: CA

Asked on: Friday, November 8, 2024 at 1:43 am EST
Answered on: Thursday, March 6, 2025 at 4:58 am EST

Question: We frequently see guys use a 2” grommet to bring a large amount of NM cable into a panel and 312.5C is clear that is a violation but, would that apply to the bare GEC? Why or why not?

Let's break down the issue of using a 2" grommet for bringing a large amount of NM cable into a panel and whether the same logic applies to a bare Grounding Electrode Conductor (GEC).

The NM Cable Situation and 312.5(C) The Problem

Stuffing multiple NM cables through a single 2" knockout and grommet into an electrical panel is a common practice, but it often violates NEC 312.5(C).


NEC 312.5(C) - Cables, Raceways, and Enclosures Entering Cabinets, Boxes, and Enclosures

This section of the NEC is concerned with the protection of conductors where they enter enclosures (like panels). It requires that where cables or raceways enter an enclosure, they must be protected from abrasion and the entrance must be properly closed.

Why It's a Violation



Abrasion

When you force multiple NM cables through a single hole, the cables can rub against each other and the edges of the knockout, especially with panel vibration. This abrasion can damage the cable insulation, creating a potential short circuit or ground fault hazard. A grommet may help, but it often doesn't provide sufficient separation and secure fastening for a large number of cables.

Proper Closing

The hole in the enclosure needs to be effectively closed. Just a grommet with multiple cables shoved through it often doesn't meet the intent of "closing" the opening to prevent the entry of foreign objects or moisture. Additionally, it doesn't provide adequate support or strain relief for the cables.


Listing and Labeling Issues

Most grommets are not listed and labeled for use with multiple cables.

The GEC Situation


Now, let's consider the bare GEC: The Question

Does the same restriction in 312.5(C) apply to a single, bare Grounding Electrode Conductor (GEC) passing through a 2" grommet into a panel?


The Answer



Generally, no, the same strict interpretation of 312.5(C) does not apply to a single, bare GEC.
Here's why: No Insulation to Abrade

The most crucial difference is that a GEC is often
bare copper. The primary concern of 312.5(C) is protecting the insulation of conductors from abrasion. Since the GEC has no insulation to be damaged at the entry point, the abrasion concern is largely eliminated.

Purpose of the GEC

The GEC's primary function is to provide a low-impedance path to ground for fault current. A little abrasion on the bare copper is not going to compromise that function.

Other Applicable Rules

While 312.5(C) may not be the primary concern, the installation must still comply with other relevant NEC sections, especially those related to grounding and bonding.

Important Considerations and Caveats for GECs


Secure Attachment

The GEC
must be securely connected to the grounding busbar or terminal within the panel using an appropriate listed connector. This is paramount.2.

Physical Protection (if necessary)

While abrasion of the conductor isn't a
primary* concern with a bare GEC, extreme physical damage might be. If the location of the GEC entry point is prone to severe mechanical damage, you might consider using a short length of conduit to protect the conductor where it enters the panel.3.

Enclosure Type

If the panel is rated for a specific environment (e.g., wet location), maintaining that rating is crucial. The GEC entry point must be sealed appropriately.4.

GEC Size

Ensure the hole size and any grommet used are suitable for the size of the GEC.5.

Manufacturer's Instructions

Always consult the panel manufacturer's instructions for specific requirements regarding grounding electrode conductor entry.

In Summary:


While 312.5(C) is a key consideration for protecting insulated conductors like NM cable entering a panel, its application to a single, bare GEC is significantly different. The primary concern of preventing insulation abrasion doesn't apply to bare conductors. However, proper secure termination, physical protection (if needed), and maintaining enclosure ratings are still essential for a safe and code-compliant GEC installation. Always consult the NEC, local amendments, and manufacturer's instructions for specific requirements. Flag for review

Previous Question Next Question