Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Voltage/Current Imbalance

User: Electromatic, Location: Virginia

Asked on: Friday, November 8, 2024 at 9:42 am EST
Answered on: Thursday, March 6, 2025 at 4:59 am EST

Question: I have a pumping station whose pumps are not running smoothly. We think it's mostly a mechanical/plumbing issue, but while investigating, I found what I consider a significant voltage and current imbalance with a motor running. The motor is 25HP, and the system is a high-leg 240V.With the motor running, I have:AB 240VBC 237VAC 235VA 51.5AB 53.5AC 44.0AOddly, I get similar results with both an old motor and a newly-installed one. Also, there is a backup generator with slightly better voltage balance (238, 238, 241), and running off it, the motor pulls 51A, 53A, 46A.Is there something I should look for to correct this, or is this a good as can be expected?TIA

Okay, let's break down this situation. You've got a voltage and current imbalance on a 25HP motor in a 240V high-leg delta system, and the imbalance persists even with a new motor and a backup generator. That points away from the motors themselves as the primary culprit. Here's a structured approach to troubleshooting

1. Understanding High-Leg Delta and Imbalances:
High-Leg Delta Challenges

High-leg delta systems, while cost-effective, are inherently more prone to imbalances than wye systems. The 'high leg' (usually phase B) has a higher voltage to ground than the other two phases, and this can contribute to voltage and current imbalances, especially when you have single-phase loads connected to the system.


Acceptable Imbalance Limits

NEMA MG-1 guidelines generally recommend the following:

Voltage Imbalance

No more than 2-3% voltage imbalance. Anything above 5% is a significant cause for concern and can damage the motor.


Current Imbalance

Generally, if the voltage imbalance is within acceptable limits, the current imbalance should also be reasonable. However, excessive current imbalance, regardless of voltage imbalance, is a problem.

2. Calculate Your Imbalances

Let's calculate the approximate voltage and current imbalances.

Voltage Imbalance Calculation


Average Voltage

(240 + 237 + 235) / 3 = 237.33V2.

Maximum Deviation

abs(240 - 237.33) = 2.67V (We use the absolute value to find the largest difference). Also abs(237-237.33) = 0.33V and abs(235-237.33)= 2.33V.
3.


Percentage Imbalance

(Maximum Deviation / Average Voltage)
100 = (2.67 / 237.33) 100 = 1.13%

Current Imbalance Calculation


Average Current

(51.5 + 53.5 + 44.0) / 3 = 49.67A2.

Maximum Deviation

abs(51.5 - 49.67) = 1.83A. Also abs(53.5 - 49.67) = 3.83A, and abs(44.0 - 49.67) = 5.67A3.

Percentage Imbalance

(Maximum Deviation / Average Current) 100 = (5.67 / 49.67) 100 = 11.4%

Analysis of Your Imbalances



Voltage Imbalance

Your voltage imbalance of approximately 1.13% is within acceptable limits (below 2-3%). This is good news, it means voltage imbalance is unlikely to be the cause of the issue.


Current Imbalance

Your current imbalance of 11.4% is

very significant
. This high level of current imbalance will shorten motor life, increase heat generation, and reduce motor efficiency.3. Troubleshooting Steps - Focus on the Electrical System

Since you've ruled out the motors themselves, focus on the upstream electrical system:

Connections

This is
critical. Loose, corroded, or oxidized connections are the #1 cause of imbalances.

Check every connection

Start at the motor starter (contactor), then work your way back to the panel, including the main disconnect, fuses (if any), and the connections at the transformer supplying the power.

Look for

Discoloration, pitting, or signs of overheating. Use a thermal camera if you have access to one.


Tighten

Torque all connections to the manufacturer's specifications. Do not overtighten!

Clean

Clean corroded connections and apply an anti-oxidant compound (like Noalox or Ox-Gard)
before re-tightening.

Cable Condition



Inspect Cables

Look for damage to the insulation, especially near connections.


Measure Cable Resistance

Use a low-resistance ohmmeter (micro-ohmmeter) to measure the resistance of each phase conductor from the panel to the motor starter. The resistance should be nearly identical for all three phases. A difference in resistance, even a small one, can cause a significant current imbalance.

Transformer Issues

This is less likely if the imbalance is similar on the generator, but still possible.


Transformer Taps

Verify that the transformer taps are set correctly for your voltage requirements. Incorrect tap settings can exacerbate imbalances.

Transformer Health

Have the transformer tested by a qualified electrician. Testing can reveal problems with the windings or core.


Grounding



Proper Grounding

Ensure that the motor, motor starter, panel, and transformer are properly grounded. A poor ground can contribute to imbalances.


Grounding Impedance

Test the grounding impedance to ensure it's within acceptable limits.

Single-Phase Loads



Identify

Map out all single-phase loads connected to the high-leg delta system.

Balance

Try to balance the single-phase loads as evenly as possible across the three phases. Overloading one phase (especially the high leg) will cause imbalances.


Relocate

If possible, consider relocating some single-phase loads to a separate, dedicated single-phase transformer or service.

Harmonics

While less likely, harmonics can sometimes contribute to imbalances. A power quality analyzer can measure harmonics.

4. Generator Considerations



Generator AVR (Automatic Voltage Regulator)

The AVR in the generator controls the output voltage. A malfunctioning AVR can cause voltage imbalances. Have the generator's AVR tested and calibrated.

Generator Winding Health

Have the generator windings tested for shorts or insulation breakdown.


Generator Connections

Double check all connections at the generator.

5. Important Safety Precautions



De-energize

Always de-energize the circuit before working on any electrical equipment. Lockout/tagout procedures are essential.


Qualified Electrician

If you are not a qualified electrician, hire one. Working with electrical systems can be dangerous.*

Proper PPE

Wear appropriate personal protective equipment (PPE), including safety glasses, gloves, and insulated tools.

6. Report Back

After you've thoroughly investigated the connections, cables, transformer (if possible), and single-phase load distribution, report back with your findings. Knowing the results of these tests will help narrow down the source of the imbalance.

In summary, the 11.4% current imbalance is a serious concern. Start with a meticulous inspection and tightening of all connections, then move on to testing cable resistance and verifying single-phase load distribution. If the problem persists, consult with a qualified electrician for more advanced troubleshooting.
Flag for review

Previous Question Next Question