User: cabledawg, Location: Boise, Idaho
Asked on: Saturday, November 9, 2024 at 3:41 pm EST
Answered on: Thursday, March 6, 2025 at 5:02 am EST
Question: Hey Guys and Girls, quick question? Is there any code on Busbar location? All the ones at this current project Im involved with have the Busbars about the 6' level inside the Telecommunication rooms. Most I have seen are usually about the 18 inch level. Just looking for a direction to go with Idaho code. Thanks in advance!
You're right to question this! 6 feet seems unusually high for busbars in a telecommunication room. Let's break down the code implications and where to look in Idaho.
Key Codes and Considerations (Generally)
NEC (National Electrical Code)
The NEC is the primary standard that Idaho adopts and amends. While it doesn't explicitly state a maximum height for busbars in all situations, it covers accessibility, working space, and guarding, which indirectly impact placement.
Idaho State Electrical Rules
Idaho adopts the NEC but often has state-specific amendments. You
MUST check the Idaho State Electrical Rules (ISER) to see if there are any modifications or additions to the NEC regarding busbar height or clearances. Working Clearances (NEC 110.26)
This is the most important section to consider. It mandates sufficient working space around electrical equipment that is likely to require examination, adjustment, servicing, or maintenance while energized. The required working space includes:
Depth
Depends on voltage to ground and condition (e.g., exposed live parts on one side and grounded parts on the other, or exposed live parts on both sides).
Width
Generally, at least 30 inches wide or the width of the equipment, whichever is greater.
Height
The most direct impact here. The NEC generally requires a minimum headroom clearance of 6 feet 6 inches (1981 mm) above the working space or the height of the equipment, whichever is greater. This is often the limiting factor.
Accessibility (NEC 110.25)
Equipment must be readily accessible. High busbars might be considered inaccessible for routine maintenance or inspection without the use of ladders or lifts.
Guarding (NEC 110.27)
If the busbars are exposed and likely to be contacted by unqualified persons, they need to be guarded. Height can be a form of guarding (e.g., if they are high enough to prevent casual contact). However, in a telecom room, access is generally limited to qualified personnel, so this is less of a factor.
Equipment Instructions
Always consult the manufacturer's installation instructions for the specific busbar system being used. They may have specific height recommendations or limitations.
Why 6 Feet is Problematic
Accessibility
Makes inspection, maintenance, and potential repairs difficult and potentially unsafe without ladders or lifts.2.
Working Clearance
While 6'6" headroom might exist, reaching up to busbars at 6' while maintaining required working distances in front of the equipment can be difficult. Consider the ergonomics of working at that height with tools.3.
Safety
Increases the risk of falls or dropped tools if personnel are working from ladders.
How to Research Idaho Code (ISER)
Idaho Division of Building Safety Website
This is your primary resource. Search for "Idaho State Electrical Rules" or "ISER." You should be able to find a downloadable PDF of the current adopted edition.2.
Navigate the ISER
Once you have the ISER document, it will generally start with the adopted NEC edition and then list Idaho-specific amendments. Carefully review the amendments to see if there are any changes to Articles 110 (Working Space) or related sections.3.
Contact Idaho Electrical Inspectors
If you're unsure about the interpretation of the code, contact the Idaho Division of Building Safety directly or a local electrical inspector in the jurisdiction where the project is located. They can provide guidance specific to your situation.
Recommended Steps
Download the current Idaho State Electrical Rules (ISER). This is critical.2. Review NEC Article 110.26 (Working Space Around Electrical Equipment). Pay close attention to the required depth, width, and height clearances.3. Carefully check the Idaho amendments to NEC Article 110.26. Look for any changes to the clearance requirements.4. Review other relevant NEC articles
110.25 (Accessibility), 110.27 (Guarding).
5.
Consult the busbar manufacturer's installation instructions.6. If in doubt, contact the Idaho Division of Building Safety or your local electrical inspector. Explain your situation and ask for clarification.
Example Arguments to Raise (If the Installation Doesn't Comply)
"The busbars at 6 feet are not readily accessible for inspection and maintenance, as required by NEC 110.25, without the use of a ladder or lift. This violates the intent of the code for safe access." "Working space clearances around the busbars at this height are insufficient to allow safe examination, adjustment, servicing, or maintenance while energized, as required by NEC 110.26. Reaching up to this height compromises the required working distances." "The busbar installation does not comply with the manufacturer's recommended installation practices (if applicable)."
In summary, while there's no direct maximum height stated in most codes, the requirements for working space, accessibility, and guarding make a 6-foot installation highly questionable and likely non-compliant. You need to do your due diligence and carefully review the Idaho State Electrical Rules and the NEC. Flag for review