Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Sizing conductors based on NEC?

User: julian padilla, Location: Houston, TX, USA

Asked on: Sunday, November 10, 2024 at 12:09 pm EST
Answered on: Thursday, March 6, 2025 at 5:03 am EST

Question: What is the minimum size Type XHHW conductor that's permitted to terminate on a transformer protected on the primary side with a 50 A breaker if the circuit breaker and equipment terminals are listed for 75°C conductor sizing? Answer: 8 AWG copper wire.▫ Comment_1: Seems to me that no math is required since conductors should not be sized at 125% of the fuse size; instead, the fuse size should be sized at 125% of the continuous load on the circuit, which means the conductor should be sized to handle that calculated load, not the other way around.▫ Comment_1: In the past, I would have used the 125% rule and calculated 50 x 1.25 = 62.5 A, and therefore oversized the wire to 6 AWG copper wire.Any insite per the NEC would minimum requirement for this conductor is appreciated.Julian

Let's break down this scenario and the NEC requirements to clarify the minimum conductor size.

Understanding the Concepts Type XHHW Conductor

A type of insulated wire commonly used for power distribution. XHHW conductors have temperature ratings (typically 75°C or 90°C).


Circuit Breaker Protection

The 50A breaker on the primary side protects the circuit supplying the transformer. This protects the conductors feeding the transformer from overcurrent conditions.

Transformer Primary vs. Secondary

It's crucial to note that the primary side conductor size is based on the current demand of the transformer
primary, not the secondary load. The primary breaker is protecting the primary conductors.

Ampacity Tables (NEC Table 310.16)

This is the fundamental table in the NEC for determining the ampacity (current-carrying capacity) of conductors based on their size, insulation type, and temperature rating.

75°C Terminations

Many breakers and equipment have terminals only rated for 75°C conductors. This means you must use the ampacity values in the 75°C column of NEC Table 310.16, regardless of whether the conductor itself has a higher temperature rating (like 90°C).


125% Rule

The 125% rule applies to continuous loads. NEC 210.19(A)(1), 215.2(A)(1), and 240.4(D) are common locations where the 125% rule may apply. However, the conductor needs to be sized at 125% of the continuous load, not the OCPD.

Analysis
1. Determine the Required Ampacity

The 50A breaker protects the conductors. The conductors must be rated to carry at least the amount of current the breaker is rated to interrupt. However, as the Comment_1 stated the breaker must be rated to carry at least 125% of the continuous load on the circuit. Therefore, the conductor needs to be sized to handle that calculated load, not the other way around. Without knowing the specific load the transformer is feeding, it is difficult to calculate the conductor size accurately. However, using the 50A breaker as the maximum allowable current, we can find the minimum conductor size.2.

Refer to NEC Table 310.16 (75°C Column)

We need to find the smallest copper conductor size (Type XHHW) with an ampacity equal to or greater than 50A when used with 75°C terminations. Looking at the 75°C column, we find: #8 AWG copper is rated for 50A #6 AWG copper is rated for 65A3.

Selection

Based on the fact that the breaker is rated for 50 amps and NEC Table 310.16 requires a wire size of 50 amps at 75 degrees, the minimum size of a copper conductor will be #8 AWG, if the load is not "continuous."

Addressing the Comments
Comment_1

The commenter is correct that conductors are sized based on the load they are expected to carry, not directly based on the breaker size, except that the wire can't be smaller than what is needed for the breaker, which is in this case #8 AWG.

Comment_2

Using the 125% rule is correct
if there is a continuous load. The conductor needs to be sized at 125% of the continuous load, not the OCPD. Therefore, with the 125% rule, the #6 AWG Copper wire is the correct size.

Conclusion


Without knowing the specific load the transformer is feeding, it is difficult to calculate the conductor size accurately. However, using the 50A breaker as the maximum allowable current, the minimum size Type XHHW conductor that's permitted to terminate on a transformer protected on the primary side with a 50 A breaker if the circuit breaker and equipment terminals are listed for 75°C conductor sizing is #8 AWG copper wire.

Important Considerations
Voltage Drop

Always calculate voltage drop to ensure it's within acceptable limits, especially for long runs. This might require using a larger conductor size than the minimum required for ampacity. NEC 210.19(A)(1) FPN 4.

Local Codes and Regulations

Always check with your local electrical inspector for any local codes or regulations that may supersede the NEC.


Professional Advice:
If you're not a qualified electrician, it's best to consult with one to ensure the installation is safe and compliant.I hope this explanation is helpful! Let me know if you have any other questions. Flag for review

Previous Question Next Question