Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: 90 volts still when off on a 3 way switch

User: PappyZz, Location: Lincoln, Nebraska

Asked on: Monday, November 11, 2024 at 4:25 pm EST
Answered on: Thursday, March 6, 2025 at 5:05 am EST

Question: I was reading some responses from a post from 2014, about the same issue I'm have with a voltage Im getting when I try my 3way switches. Didn't seem to be a real consensus on the issue then. But I do visit here a lot. Now I'm a member and im having this same issue.The house is from the 60s and I've run new wire to these switches which are also new. But I'm getting 90 volts whenever I switched either switch,any ideas on what to look for or try?

Okay, let's break down what might be happening with your 3-way switch setup and that strange 90-volt reading. Getting a "phantom voltage" in wiring, especially with new wiring, is a common electrical issue, but it can still be dangerous, so take precautions and don't assume it's harmless.

Understanding 3-Way Switches

First, a quick refresher on how 3-way switches work. You have two switches that control a single light fixture. Both switches have the ability to turn the light on or off, regardless of the position of the other switch. This is achieved using "traveler" wires that connect the two switches, and the light is connected to one of the switches.

Why are you getting 90 volts?

Several things can cause a voltage reading when you expect zero. Here's a breakdown of potential causes: Induced Voltage (Capacitive Coupling / Phantom Voltage)

This is the most likely culprit, especially with new wiring. When you run new wires alongside other live wires (like in a cable or conduit), the electrical field from the live wires can induce a small voltage onto the unpowered wires. Your voltmeter, being a high-impedance device, can pick up this induced voltage, even though it's not capable of delivering any significant current. This is often referred to as "phantom voltage."


Explanation

Think of it like a very weak capacitor being formed between the live wires and the unpowered wires.

Why 90 volts?

The amount of induced voltage depends on several factors, including the length of the parallel run, the proximity of the wires, and the voltage of the live wire.


Improper Grounding

A poor or missing ground connection can cause voltage to "float" and give you misleading readings. Make sure the grounding wire is correctly connected at all points in your circuit.

Shared Neutral Issues (Multi-Wire Branch Circuits)

If your home has multi-wire branch circuits (where two hot wires share a single neutral), problems with the neutral can cause voltage imbalances and odd readings on unused wires. This is less likely if you ran new wiring specifically for the 3-way switches, but it's worth considering if the circuit interacts with other circuits.


Leakage Current

While less common, some electrical devices or wiring can have a small amount of leakage current, which can register as a voltage on a high-impedance voltmeter.

Wiring Errors

Double-check all your wiring connections at both switches and at the light fixture. Even a small wiring mistake can cause unexpected voltage readings. Common issues include:
Neutral and ground wires reversed. One of the traveler wires connected to the neutral or ground. A loose wire that is making intermittent contact.

Faulty Switch

Although unlikely with new switches, one of the 3-way switches might have an internal defect causing a voltage leak.

Troubleshooting Steps


Here's a systematic approach to diagnose and address the issue:1. Verify Grounding

Ensure that the ground wire in your cable is properly connected to the ground terminal in the switch boxes and at the electrical panel. Use a multimeter to verify continuity between the ground wire and a known good ground (e.g., a cold water pipe, but be very careful using plumbing as a ground). Make sure there's a solid connection to the metal boxes (if applicable) using grounding screws.2.

Turn Off the Power



SAFETY FIRST!
Turn off the circuit breaker supplying the 3-way switch circuit before doing any further testing or wiring changes.3. Check Wiring Diagram

Make absolutely certain that you've wired the 3-way switches according to the correct wiring diagram. There are many 3-way switch diagrams online. The basic diagram will show:
Power source ("Line") connected to the common terminal of one switch. The light fixture connected to the common terminal of the other switch. Two "traveler" wires connecting the remaining terminals of both switches.4.

Measure Voltage to Ground

With the power OFF. Check voltage from each wire (including the neutral and ground) to a known good ground. There should be ZERO volts.5.

Measure Voltage with a Load (if induced voltage is suspected)

If you suspect induced voltage, try measuring the voltage with a load connected. A simple way to do this is to connect a low-wattage incandescent light bulb (like a nightlight bulb) in series with the wire you're measuring and then measure the voltage across the bulb. If the voltage drops significantly when the bulb is connected, it's likely induced voltage.

Do this with the power on, so be very careful!
6. Isolate the Switches

Disconnect the traveler wires at one of the switches. Then measure the voltage again. If the voltage disappears, the problem is likely somewhere between the two switches. Do the same at the other switch.7.

Inspect Wire Runs

Visually inspect the entire length of the new wiring for any damage, nicks, or breaks in the insulation. Ensure the wiring is properly secured and not pinched or rubbing against anything.8.

Check for Shared Neutral (Multi-Wire Branch Circuits)

If you suspect a shared neutral, carefully trace the neutral wire from your 3-way switch circuit back to the electrical panel. See if it shares a neutral with any other circuits. If so, examine the connections at the panel and look for any loose or corroded connections. This is advanced and requires caution. If you're not comfortable working in the panel, call an electrician.9.

Consider an Electrician

If you've gone through all these steps and are still unable to find the source of the voltage, it's time to call a qualified electrician. They have specialized tools and knowledge to diagnose and fix electrical problems safely.

Important Safety Considerations



Turn off the power

Always turn off the circuit breaker before working on any electrical wiring.

Use insulated tools

Use tools with insulated handles to prevent electrical shock.


Test your work

After making any wiring changes, double-check your work and test the circuit to ensure it's working correctly.

Don't assume it's harmless

Even a small voltage can be dangerous, so treat all electrical wiring with respect.


When in doubt, call a professional:
If you're not comfortable working with electricity, or if you're not able to resolve the problem, call a qualified electrician.Let me know if you have any questions about any of these steps. Good luck, and be safe! Flag for review

Previous Question Next Question