Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: AF labels on load bank or camlock?

User: lielec11, Location: Charlotte, NC

Asked on: Tuesday, November 12, 2024 at 3:49 pm EST
Answered on: Thursday, March 6, 2025 at 5:08 am EST

Question: I'm curious the communities opinion on putting arc flash labels on items that are normally off and only used in a generator testing environment. I'm talking about things like a load bank or a camlock box that may be used to connected to a load bank or a roll-up generator. IMO we do not typically include them in our study as they don't carry short circuit ratings, have devices to coordinate with, nor are they typically operated on live. But we have a client who is basically going item by item on a one-line claiming they are part of the scope. I want to appease them but I'm not even sure if you can quantify any results. Thoughts?

You're in a tricky spot, balancing client expectations with practical and technical considerations. Here's a breakdown of considerations and potential approaches to address the client's concerns regarding arc flash labeling of infrequent generator testing equipment

Understanding the Client's Perspective

First, try to understand why the client wants these labels so badly. Possible reasons include: Risk Aversion

They want to be
seen as covering all bases, regardless of actual risk. Compliance, even if perceived, is paramount.

Misinterpretation of Regulations

They might believe everything electrical requires a label.

Specific Incident in the Past

Perhaps they had a near-miss or accident involving temporary equipment and are overreacting.


Lack of Trust in Your Expertise

They may not fully trust your assessment that the risk is low.

Future-Proofing

They might anticipate these items being used in different scenarios in the future where arc flash risk
could be present.

Your Valid Points

You're right to question the necessity and value of arc flash labels on equipment used infrequently and not normally energized. Here's why:


Arc Flash Study Scope

Arc flash studies typically focus on permanently installed equipment that is routinely operated and exposed to potential arc flash hazards. Temporary equipment, especially if de-energized during connection and disconnection, falls outside that scope.

Lack of Coordination and Short Circuit Contribution

As you mentioned, load banks and camlock boxes don't contribute to short circuit current or have protective devices to coordinate with. Their arc flash risk is directly tied to the
upstream source (generator or building power), not their own characteristics.

Limited Actionable Information

What would an arc flash label say on a load bank? It would likely state the incident energy level based on the upstream source, which doesn't change the way the load bank is operated. The PPE requirements will be determined at the source.

Potential for Misinterpretation

A label that is always referring to a different upstream device could easily lead to confusion.


De-energized Operation

If the equipment is always connected and disconnected de-energized, there is no arc flash hazard.

Addressing the Client's Concerns: A Balanced Approach


Here's a strategy to address the client's concerns while maintaining a technically sound position:1. Open Communication

Have a face-to-face (or video) discussion with the client. Start by actively listening to their concerns and reasons for wanting the labels. Don't be dismissive.2.

Educate, Don't Argue

Explain the purpose of arc flash studies and labels: to protect workers during normal operation and maintenance of energized equipment. Explain why the typical scope excludes infrequently used, de-energized equipment.3.

Risk Assessment Alternative

Instead of arc flash labels, propose a written risk assessment for generator testing. This document would detail the procedures for safe connection and disconnection of the load bank and camlock box, emphasizing de-energized operation, proper grounding, and visual inspection before energizing. This approach is more tailored and appropriate for the specific scenario.4.

Source Labeling

Instead of labeling the load bank or camlock, focus on labeling the source (generator or building connection point). Ensure the source label accurately reflects the potential arc flash hazard when that source is used to power the load bank. This provides the relevant information in the right location.5.

Procedure Focus

Instead of labeling, focus on the procedures for generator testing. A well-written and enforced procedure, combined with training, is more effective than labels alone. The procedure should include: Lockout/Tagout (LOTO) verification. Visual inspection of connections. Grounding verification. Confirmation that the load bank and camlock box are suitable for the voltage and current levels.6.

Conditional Labeling (Compromise Option)

If the client insists on labels, consider a conditional approach:

"This Equipment is Powered From [Source]. Refer to the Arc Flash Label on [Source] for Hazard Information When Powered From That Source."
This avoids creating a label with potentially misleading or inaccurate information. Include a QR Code

The label can contain a QR code that links to a document outlining the specific procedures for safe connection and disconnection of the equipment, emphasizing de-energized operation.7.

Document Everything

Regardless of the outcome, document your discussions with the client, the rationale for your recommendations, and the client's final decision. This protects you from future liability.

Example Risk Assessment Elements


A risk assessment for generator testing should include: Hazard Identification

Electrical shock hazard during connection/disconnection. Arc flash hazard from the generator or building source. Mechanical hazards (lifting, moving equipment). Environmental hazards (weather, noise).

Risk Evaluation

Likelihood of occurrence. Severity of potential injuries.

Control Measures

De-energized connection/disconnection procedures. LOTO procedures. Use of appropriate PPE (based on source arc flash hazard). Proper grounding procedures. Training on safe operating procedures.

In Summary


Arc flash labels on infrequently used, de-energized equipment like load banks and camlock boxes are generally not necessary or technically justified. Focus on a well-documented risk assessment, safe operating procedures, and proper labeling of the power source. Communicate effectively with the client to address their concerns and arrive at a solution that protects workers while remaining practical and cost-effective. Document everything! Flag for review

Previous Question Next Question