User: Roddick, Location: Chicago
Asked on: Tuesday, November 12, 2024 at 11:00 pm EST
Answered on: Thursday, March 6, 2025 at 5:09 am EST
Question: HelloI will do soon a new power for EV car in detached garage.There is already 1" conduit underground.I found that almost at the house about 2 feet from the entry the pipe is blocked with dirt and mud so I cannot change the wires.I will cut pipe at this point and replace it with new piece of rigid pipe.Unfortunately I cannot make a thread so my question is if there is any direct burial threadless coupling I can use.Thank you.
Okay, I understand. You have a blocked 1" underground conduit run between your house and detached garage that you want to use to run power for an EV charger. You need to cut the conduit near the house and repair it, but you can't thread the existing conduit. You're looking for a direct burial-rated threadless coupling to connect the old and new sections.Here's a breakdown of your options and things to consider
Yes, Direct Burial Threadless Couplings Exist!
They are specifically designed for situations like yours. They are often called "Compression Couplings" or "Set-Screw Couplings"Key Considerations and Recommendations
Material Compatibility
Ideally, use the same material as your existing conduit. If the existing conduit is Rigid Metal Conduit (RMC), use a steel compression coupling rated for direct burial. If it's PVC, use a PVC coupling rated for direct burial. Mixing metals underground can lead to corrosion. Galvanized steel is usually the standard for RMC. Steel vs. PVC
RMC is a good choice because it gives you grounding through the conduit.2.
Direct Burial Rating (Crucial!)
This is non-negotiable. The coupling MUST be specifically rated for direct burial. Look for markings that indicate it's suitable for underground use. These couplings are designed to be watertight and corrosion-resistant in the soil.3. Type of Coupling
Compression Couplings
These use a compression ring that tightens down on the conduit when the coupling is tightened. These are generally considered a good option for watertight seals. They often require tightening with wrenches.
Set-Screw Couplings
These use set screws to clamp onto the conduit. While they can be used, ensure they are specifically listed and rated for direct burial and are suitable for the conduit material. Make sure the set screws are tight and that they are stainless steel or otherwise corrosion-resistant.4.
Grounding (Very Important!)
RMC Conduit
If you're using RMC, the conduit itself can serve as a grounding conductor. Make sure the couplings are properly tightened to maintain electrical continuity. You may also need to run a separate grounding wire.
PVC Conduit
PVC conduit cannot be used as a grounding conductor. You must run a separate grounding wire inside the conduit along with your power conductors.5.
Size and Type
Double check that you are buying the correct size coupling for 1" conduit!
Steps to Take
Excavate and Expose the Existing Conduit
Carefully dig around the conduit on both sides of where you plan to cut. Give yourself enough room to work.2.
Cut the Conduit
Use a hacksaw, pipe cutter, or reciprocating saw to cut the conduit cleanly. Ensure the cut is as square as possible for a good fit with the coupling.3.
Deburr the Cut Ends
Use a file or deburring tool to remove any sharp edges or burrs from the inside and outside of the cut conduit ends. This helps prevent damage to the wires when you pull them through.4.
Install the Coupling
Follow the manufacturer's instructions for the specific coupling you purchased. Loosen all screws or compression nuts on the coupling. Slide the coupling onto one end of the conduit. Slide the other end of the conduit into the coupling. Tighten the screws or compression nuts according to the manufacturer's specifications. Double-check that the coupling is securely attached to both conduit sections.5.
Run the Wiring
Carefully pull the new wires through the repaired conduit. Use wire pulling lubricant to make the job easier and prevent damage to the wire insulation. Make sure you use the correct gauge wire for the amperage and distance of the EV charger circuit.6.
Backfill and Compact
Carefully backfill the trench around the repaired conduit with soil. Compact the soil in layers to prevent settling.7.
Labeling
Label the circuit appropriately in your electrical panel.
Important Safety Considerations
Turn off the power! Before doing any electrical work, turn off the power to the circuit at the breaker panel. Double-check that the power is off using a non-contact voltage tester. Call a qualified electrician if you're not comfortable. Working with electricity can be dangerous. If you're not experienced, hire a licensed electrician to do the work. EV chargers require specific wiring and safety considerations, and improper installation can be a fire hazard or electrocution risk. Check Local Codes and Permits
Before starting any electrical work, check with your local building department to see if you need a permit. They can also advise you on local code requirements.
Burial Depth
Make sure the conduit is buried at the correct depth according to local codes. This is to protect the conduit and wiring from damage.
Where to Find Couplings
Electrical Supply Stores
These stores are the best place to find a wide selection of direct burial-rated couplings.
Home Improvement Stores (e.g., Home Depot, Lowe's)
They usually carry a limited selection.
Online Retailers (e.g., Amazon)
Make sure the coupling is from a reputable manufacturer and is specifically listed for direct burial.
Example Products to Look For (Disclaimer: Always verify suitability for your specific application)
For RMC
Look for "Rigid Conduit Compression Coupling - Direct Burial Rated" or "Rigid Conduit Set-Screw Coupling - Direct Burial Rated". Look for brands like Bridgeport, Thomas & Betts, or similar well-known electrical brands.
For PVC
Look for "PVC Conduit Coupling - Schedule 40/80 - Direct Burial Rated."
Final Recommendation:
Given the importance of a reliable connection for your EV charger, I strongly* recommend consulting with a qualified electrician. They can assess the situation, ensure the repair is done safely and correctly, and ensure the wiring meets all applicable codes. They can also help you choose the correct gauge wire and breaker size for your EV charger. Flag for review