Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Designing with bifacial modules

User: ggunn, Location: Austin, TX, USA

Asked on: Thursday, November 14, 2024 at 2:08 pm EST
Answered on: Thursday, March 6, 2025 at 5:13 am EST

Question: I have designed a few PV systems with bifacial modules, but they have all been low tilt ballasted systems so I ignored the bifacial aspect. Now I am designing a ground mounted system and I am not sure what to do about it. It's getting hard to find modules that are NOT bifacial modules these days and I am not sure how to treat them. Thoughts?

You're right, bifacial modules are becoming increasingly common, and ignoring their potential on a ground-mounted system is a missed opportunity. Let's break down how to treat them properly

1. Understanding Bifacial Gain:
What it is

Bifacial gain refers to the extra energy production you get from the
rear side of the module. Sunlight reflects off the ground (albedo), the mounting structure, and any surrounding objects, providing irradiance to the rear cells.

Factors Affecting Gain

The amount of bifacial gain is affected by many factors:

Albedo

The reflectivity of the ground surface. Higher albedo (like fresh snow) means more reflected light and more gain. Typical values range from 0.2 (dark soil) to 0.8 (fresh snow). Gravel, concrete, and light-colored surfaces are good choices.


Mounting Height

Higher mounting heights allow more light to reach the rear. This is especially important.

Row Spacing (GCR)

A lower Ground Coverage Ratio (GCR - the ratio of array area to total land area) with wider row spacing allows more light penetration between rows to the rear of the modules.


Tilt Angle

Lower tilts allow for more light reflected from the ground and bouncing on the back of the modules.

Module Characteristics

Module design (cell configuration, glass type) and bifaciality factor (ratio of rear to front power) impact performance.

2. Tools and Methods for Modeling Bifacial Performance

This is where things get more complex, but here's a tiered approach:


Simple Rules of Thumb (Quick Estimates)



Very Conservative

Assume 5-10% gain as a
very conservative estimate, especially if you have lower mounting heights and higher GCR. This is better than ignoring the bifaciality completely.

Moderate

Assume 10-20% gain for typical ground mount systems with good albedo and reasonable mounting height.

Important

These are
estimates only. They should be used for preliminary assessments or when more detailed data is unavailable. Don't base your final design on these alone.

Online Bifacial Calculators

Some module manufacturers have online bifacial performance calculators. You input basic site data, module specs, and layout details, and they give you an estimated bifacial gain. These can be a good starting point. Search for "[Module Manufacturer Name] Bifacial Calculator". NREL System Advisor Model (SAM) is another great free tool with built in bifacial modeling capabilities.

Advanced Simulation Software (Highly Recommended)



PVsyst

Industry-standard software. It has a detailed bifacial model that considers module characteristics, shading, albedo, row spacing, tilt, and mounting height. Requires a paid license.

Helioscope

Cloud based software with bifacial capability (paid).

3. Design Considerations for Bifacial Systems



Ground Preparation



Albedo Enhancement

Consider using light-colored gravel, crushed white stone, or even a reflective membrane under the array to increase albedo. Weed control fabrics in lighter colors can also help.


Grading

Ensure the ground is level and well-drained to prevent water accumulation that could reduce albedo or cause corrosion.

Mounting Structure



Height

Design for higher mounting heights to maximize rear-side irradiance. Aim for at least 0.5 meters (1.6 feet), and ideally higher if the cost is justified.

Reflection

Consider using reflective materials on portions of the racking structure to further boost rear-side irradiance. However, avoid creating glare problems.


Minimize Shading

Design the racking to minimize shading on the rear of the module.

Row Spacing



GCR Optimization

Balance land use with bifacial gain. A lower GCR (wider row spacing) allows more light to reach the rear, but requires more land. Run simulations to find the optimal GCR for your project economics.

Module Selection



Bifaciality Factor

Choose modules with a high bifaciality factor (the ratio of rear-side power to front-side power).

Glass Type

Consider the glass type on the rear of the module. Some glass may have better light transmission characteristics.


Tilt Angle



Lower Tilts

While lower tilts may slightly decrease front-side production, they can significantly increase rear-side gain due to increased ground reflectance. Simulations are critical.


Shading Analysis

Perform detailed shading analysis, especially considering the rear side of the modules. Shading on the rear can significantly reduce bifacial gain.

Stringing and Inverter Selection

Bifacial modules can generate slightly different current and voltage characteristics than monofacial modules. Consult the module datasheet and inverter specifications to ensure compatibility. MPPT (Maximum Power Point Tracking) is especially important for maximizing energy harvest.

4. Real-World Considerations and Monitoring



Snow Cover

Snow can drastically increase albedo, but it can also block the rear of the modules. Consider snow removal strategies in snowy climates.

Vegetation

Vegetation growth under the array can reduce albedo. Implement vegetation management plans.


Monitoring

Install monitoring equipment to track the actual energy production and compare it to your simulations. This will allow you to validate your design and make adjustments as needed. Consider including sensors to measure rear irradiance.

In summary:
Don't ignore the bifacial aspect, especially on ground-mounted systems. Start with conservative estimates, use simulation software to optimize your design, and consider the practical aspects of ground preparation, mounting, and monitoring. By doing so, you can significantly increase the energy production of your PV system. Flag for review

Previous Question Next Question