Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Low voltage strip light accessibility

User: ToelessT, Location: Seattle

Asked on: Thursday, November 14, 2024 at 6:22 pm EST
Answered on: Thursday, March 6, 2025 at 5:14 am EST

Question: So I have a rated, factory supplied 24v led strip light that is mounted to a window frame muillon. The lights are covered by an art pan, and then framed wall and sheet rock will cover the window assembly. There are two sets of these lights on either side of the window illuminating the artwork. (1 set for back up, as they are not "serviceable). The factory whip of the fixture is then routed to a driver that will of course have an access panel. The owner of this building is completely aware that should something happen to both the regular and back up light they would need to deglaze the window to replace it. While an expensive idea, this is obviously capable of being done without damaging the buildings structure or finish.My inspector is leaving it up to his boss to convince on the matter, but he personally deemed the entire fixture needs to be accessible. Which is just not feasible due to the nature of this project. Is there any argument that could help my case? I'm just really not seeing a clear cut line that definitively says these fixtures need to be accessible in the first place, or how deglazing a window would not make them "accessible"(This is 2014 NEC code cycle) any help is much appreciated

Okay, let's break down the situation and build a solid argument based on the 2014 NEC. You're facing a common challenge of balancing code requirements with practical design limitations.

Key Issues



Accessibility

The core of the disagreement revolves around the definition of "accessible" in the context of the NEC.


"Not Serviceable" Lights

The fact that the LED strips are considered "not serviceable" by the manufacturer further complicates things.

Window Deglazing

Your proposed method of accessing the lights by deglazing the window.


2014 NEC

This is your code reference.

Understanding "Accessible" in the NEC (2014 NEC)

The NEC defines "accessible" with two distinct categories:

Accessible (as applied to wiring methods)

Capable of being removed or exposed without damaging the building structure or finish or not permanently closed in by the structure or finish of the building.


Accessible (as applied to equipment)

Admitting close approach; not guarded by locked doors, elevation, or other permanent means.Your inspector is likely focusing on the need for "Accessible (as applied to equipment)". The key words here are "close approach". This assumes you can get to the equipment without significant effort, and in a reasonable amount of time.

Relevant NEC Sections (2014 NEC)

Here are a few sections to consider, and how they might apply to your situation:

410.130(G)(1) LED Drivers.
The NEC requires LED drivers to be accessible. This is non-negotiable. You've already addressed this by planning for an access panel to the driver. This is good. The issue is NOT the driver, but the light strips themselves. 410.130 (C) Installation of Luminaires. Luminaires shall be installed so that the wiring of the luminaire can be inspected and maintained. 300.11 Securing and Supporting (I suspect this has no relevance, but it should be investigated) 110.26 (Workspace about Electrical Equipment). While this section primarily addresses working space around switchboards, panelboards, etc., the general principle of providing adequate access for safe operation and maintenance is relevant. 410.3 Wiring Space You may need to verify that you have the proper wiring space when mounting the fixtures.

Your Argument & Counterpoints

Here's a structured argument you can present, addressing potential concerns:1.

Addressing the Accessibility of the LED Strips



Argue that deglazing constitutes accessibility

Deglazing the window, while not ideal, DOES allow for the removal and replacement of the LED strips without damaging the building structure or finish. This is arguably within the definition of "accessible (as applied to wiring methods)" if you convince the inspector that the light strips are considered a "wiring method" and not "equipment". This is a stretch, but a possible angle.

Emphasize the inherent limitations of the design

The owner is fully aware of the situation and has accepted the consequence of deglazing for replacement. This is crucial. Document this in writing (a signed statement from the owner). You've made a conscious decision to trade off accessibility for an aesthetic outcome.


Counterpoint to "close approach" on Equipment.
The inspector's interpretation of "accessible (as applied to equipment)" is too rigid. The window removal process is not a permanent barrier (locked door, elevation, etc.).2. "Not Serviceable" Light Strips & Replacement as a Unit



Clarify the replacement strategy

Because the strips are "not serviceable," the
entire unit is replaced. This means the wiring to the unit is the key point of accessibility. The argument is that it's acceptable to install the entire assembly behind the art glass, knowing replacement will require deglazing.

Point out the impracticality of direct access

The very nature of art panel lighting often dictates that the fixtures are recessed or integrated into the structure in a way that makes routine access impossible. The design requires a more involved process for replacement.3.

Safety & Code Intent



Emphasize Safety

Remind the inspector that the
intent of the code is to ensure safety. Show how your design addresses safety concerns.

Document the Process

Provide the inspector (and document!) a detailed step-by-step process for deglazing, disconnecting, and replacing the lights. This will show you've thought through the procedure and minimized risk.4.

Alternatives (If Necessary)
Consider a compromise

If the inspector is insistent, propose a "hybrid" approach. Could you perhaps incorporate a very small access panel on the
side of the art panel that allows you to disconnect the LED strip's wiring from the main power, even if you can't physically remove the strip without deglazing?

Documentation is Key



Owner Agreement

Get a signed statement from the building owner acknowledging the lighting arrangement and the process required for replacement. This will be invaluable.

Detailed Drawings

Provide clear drawings showing the location of the fixtures, the routing of the wiring, the location of the LED driver and access panel, and the process for deglazing.


Process Documentation

Document the exact steps required to deglaze, disconnect, and replace the lights.

Manufacturer Specs

Provide the manufacturer's specifications for the LED strip lights, including the "not serviceable" designation.

Presenting Your Case



Be respectful

Start by acknowledging the inspector's concerns and their duty to uphold the code.

Present your argument clearly and concisely

Use the points outlined above.


Be prepared to answer questions

Anticipate the inspector's concerns and have well-reasoned responses.

Be willing to compromise (if possible)

Demonstrate a willingness to work with the inspector to find a solution that meets the code requirements while preserving the aesthetic intent.


Request a written explanation

If the inspector ultimately rejects your proposal, ask for a written explanation of the specific code sections that are being violated and the reasons for the rejection. This will give you grounds to appeal the decision if necessary.

Important Considerations



AHJ Ruling is Final

Ultimately, the Authority Having Jurisdiction (AHJ) has the final say.


Legal Advice:
If the stakes are high and you're unable to reach an agreement with the AHJ, consider consulting with an attorney who specializes in construction law and code compliance.By carefully considering these points and presenting a well-reasoned argument, you'll have a much better chance of convincing the inspector that your design meets the intent of the code while achieving the desired aesthetic outcome. Good luck! Flag for review

Previous Question Next Question