Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Free air cable installed at 12’ above finished floor protected?

User: Isaiah, Location: Baton Rouge

Asked on: Thursday, November 14, 2024 at 7:39 pm EST
Answered on: Thursday, March 6, 2025 at 5:15 am EST

Question: We have 3/C w/Grd cable free air suspended for approximately 3’ from a C fitting to a 3 phase 480V HeaterConstruction is saying the cable is “protected” since it’s installed too high to be hit by a forklift or other objects. NEC requires cable to be protected from physical damage-does the above installation meet the intent of the Code?

This is a tricky one, and the answer isn't a clear "yes" or "no." Here's a breakdown of why, and how to approach the situation

Arguments for NOT meeting the NEC intent:
"Free Air Suspended" Suggests Movement and Potential for Damage

"Free air suspended" implies the cable can swing or move. Even if it's high, the movement itself, especially over time, could cause:


Abrasion

Rubbing against the C fitting or the heater enclosure could wear down the insulation.

Stress on Connections

Repeated swinging can loosen connections inside the C fitting or at the heater terminals.


Fatigue

The cable itself could experience metal fatigue due to repeated bending.

Potential for Dropped Objects

While a forklift might not directly hit it, consider other scenarios:


Tools or materials falling from above

A worker on a ladder could drop something.

Accidental impacts from other equipment

A pipe being carried, a long piece of material, etc., could swing into the cable.


Lack of Definition of "Protected"

The NEC doesn't explicitly define what "protected from physical damage" means in every situation. It's often left to the authority having jurisdiction (AHJ) to interpret.

Code Articles to Consider



NEC 300.4(D) Protection from Physical Damage

This is the general requirement. The key is whether the free air suspension provides adequate protection.

NEC 334.15 Exposed Work

This article applies to NM cable, but the principles are relevant. It discusses how NM cable must be protected in exposed areas.


Other relevant articles based on the specific cable type used (e.g., MC, TC)
Arguments for potentially meeting the NEC intent (but less likely)



Height

If the cable is
genuinely installed at a height that realistically makes accidental damage extremely unlikely, and the installation is very secure (minimal movement), then it might be argued as protected.

Inspection and AHJ Approval

Ultimately, the AHJ (inspector) has the final say. If they inspect the installation and are satisfied that the height and installation method adequately protect the cable, they could approve it.

Recommendations


Provide Physical Protection

The best and safest approach is to add physical protection, even if it seems redundant. Here are some options:

Conduit

Extend rigid metal conduit (RMC) or intermediate metal conduit (IMC) down from the C fitting and up to the heater. This provides robust protection.


Flexible Metal Conduit (FMC)

Use FMC or liquidtight flexible metal conduit (LFMC) for the short run, especially if vibration is a concern. Make sure to use appropriate fittings.

Cable Tray

If there are multiple cables in the area, consider using a short section of cable tray to support and protect them.


Strut and Clamps

Install a section of strut with appropriate cable clamps to provide support and keep the cable secure.2.

Secure the Cable

Regardless of whether you add further protection, ensure the cable is securely supported to minimize movement and stress. Use appropriate cable supports and clamps designed for the cable type.3.

Consult the AHJ

Before making any changes, discuss the situation with the local electrical inspector. Explain why you believe the current installation might not meet the NEC intent, and get their guidance on acceptable solutions. This is crucial.4.

Document Everything

Keep records of your communications with the AHJ, the rationale for your chosen protection method, and the installation details.

In summary:


While the "out of reach" argument might sound plausible, it's generally not sufficient to meet the NEC's intent for protection from physical damage, especially with a "free air suspended" cable. The risk of abrasion, stress, accidental impact, and the AHJ's interpretation all point towards adding physical protection to the cable. It's best to be proactive and install adequate protection to ensure safety and code compliance. Flag for review

Previous Question Next Question