User: bcm, Location: Atlanta, Georgia
Asked on: Friday, November 15, 2024 at 12:40 pm EST
Answered on: Thursday, March 6, 2025 at 5:16 am EST
Question: Happy Friday, Sparky Friends!I have a client who wants to install a panelboard to feed some antenna rectifiers in a hotel building. The building has a 120/208V, 3 phase, 4000A service. The client refuses to tell me (or doesn't know?) if the rectifier equipment can accept 208V (I've been asking for over a month), so I can only assume it won't accept 208v.They want to install a 120/240V, 200A, 1 phase panelboard with interlocked ATS (connected to a natural gas gen) to serve the rectifiers which require 2P breakers for each rectifier.I would put in a 200A, 120/208V, 3ph breaker in the MDP, route the 5 wires (L-L-L-N-G) in conduit up to the roof level, and use a fused disconnect mounted near the panel.At this point, I am trying to figure out the best way to handle the voltage change. I thought about using buck/boost, but going from 3 phase to 1 phase is going to leave one leg unused and thus potential for load balance issues, right? That's going to happen no matter what since they seem hell-bent on the 200A, 120/240V, 1 phase panel (probably because they already have it). I haven't dealt with this scenario before. Would I use a buck/boost transformer on each of the 2 legs going into the panel or is there a single transformer that could handle it?Thanks for your input!
Okay, this is a common, but tricky, situation. You've identified some important considerations. Let's break it down, and then discuss solutions
Understanding the Challenges
Voltage Mismatch
208V available, but needing 240V.
Phase Mismatch
3-phase supply, but 1-phase panel demand.
Load Balancing on the Service
Tapping a large single-phase load from a 3-phase service always introduces imbalance. You need to minimize it as much as possible.
ATS Integration
Adding the automatic transfer switch (ATS) complicates the power distribution and transformer selection.
Client Stubbornness
Dealing with a client who may already have equipment and is resistant to changing their plans.
Considerations Before Proceeding1. Push Harder for Rectifier Voltage Information
This is still your number one priority. A month is far too long to wait. Explain to the client the cost implications of guessing. Explain that the solution could change dramatically if they tell you the voltage. Can you contact the equipment manufacturer directly, or the supplier? Be firm, but professional. If the rectifiers can handle 208V, this whole problem gets much easier.2.
Calculate Actual Load
A 200A panel implies a significant potential load. Find out the actual continuous load the rectifiers will draw. Oversizing the panel and associated equipment could be very costly and increase load imbalance on the service.3.
Utility Consultation
A 200A single-phase load from a 4000A 3-phase service can cause issues for the utility. While it's likely within acceptable limits, it's prudent to inform them of the planned load and get their feedback, especially if there's already marginal voltage regulation in the area. They may want you to perform a load study.4.
Demand Factors
Are you able to apply a demand factor to the rectifiers? Are all the rectifiers running 24/7?
Possible Solutions (Assuming the Rectifiers NEED 240V)Option 1: 3-Phase to 1-Phase Transformer Description
This is the most common and usually best solution in this situation, but it's also the most expensive. You would use a properly sized 3-phase to 1-phase transformer designed specifically for converting 208V 3-phase to 240V single-phase. These are available.
Wiring
Take all 3 phases from the 208V, 3-phase breaker in the MDP. Connect the transformer primary to the 208V, 3-phase supply. Connect the transformer secondary to the 200A, 120/240V panel. Ensure proper grounding.
ATS Integration
You'll need to either size the transformer to handle the generator input as well (if the generator provides 208V 3-phase), or use a separate single-phase transformer for generator power. The ATS switches between the utility-supplied 240V and the generator-supplied 240V.
Advantages
Properly handles the phase conversion. Generally more efficient and reliable than other options. Best option for minimizing load imbalance on the 3-phase service.
Disadvantages
Most expensive option. Requires more space for the transformer. Higher upfront cost.
Option 2: Buck-Boost Transformers (Less Recommended) Description
Use two buck-boost transformers. One on each leg of the incoming 208V to increase it to 240V.
Wiring
Take two phases from the 208V, 3-phase breaker in the MDP (e.g., L1 and L2). Run each phase through a buck-boost transformer. Configure them to boost the voltage by the necessary amount. Connect the boosted phases to the 200A, 120/240V panel. Leave one phase of the MDP breaker unused.
ATS Integration
Similar to option 1, you'll need to coordinate the voltage transformation on the generator side. Ensure the ATS switches properly between the utility and generator sources.
Advantages
Potentially less expensive than a full 3-phase to 1-phase transformer (depending on the size needed). May be easier to find off-the-shelf.
Disadvantages
Significant load imbalance on the 3-phase service. You're only using two legs. Buck-boost transformers can be less efficient for this application compared to a dedicated 3-phase to 1-phase transformer. Heat generation can be an issue with constant, large loads. Increased complexity and potential points of failure.
Option 3: Autotransformer Description
Using an autotransformer to step-up the voltage. This is different from a typical isolation transformer as it shares windings between the primary and secondary.
Wiring
Take two phases from the 208V, 3-phase breaker in the MDP (e.g., L1 and L2). Connect the autotransformer primary to the 208V, 1-phase supply. Connect the autotransformer secondary to the 200A, 120/240V panel. Leave one phase of the MDP breaker unused.
ATS Integration
You'll need to coordinate the voltage transformation on the generator side. Ensure the ATS switches properly between the utility and generator sources.
Advantages
Potentially less expensive than a full 3-phase to 1-phase transformer (depending on the size needed). Can be more efficient than two buck/boost transformers. Smaller footprint than a transformer.
Disadvantages
Significant load imbalance on the 3-phase service. You're only using two legs. Lack of isolation between the primary and secondary, which can be a safety concern in some applications. Heat generation can be an issue with constant, large loads.
Recommendation Strongly advocate for Option 1
The 3-phase to 1-phase transformer is the most professional and electrically sound solution. It minimizes load imbalance and provides a clean voltage conversion. Make a case for the long-term reliability and reduced operational costs.
If Option 1 is impossible, consult a qualified electrical engineer
They can perform a load study, analyze the system impact, and design a solution using either buck-boost transformers or an autotransformer that minimizes the negative effects. Be prepared for potential upgrades to the service if the load imbalance is excessive.
Clearly document your recommendations and the client's decisions in writing
This protects you in case of future problems.
Additional Considerations Overcurrent Protection
Ensure proper overcurrent protection (fuses or breakers) on both the primary and secondary sides of any transformer used.
Transformer Sizing
Size the transformer based on the actual continuous load of the rectifiers, plus a safety factor (typically 25%). Don't just assume the panel's 200A rating is the load.
Transformer Location
Consider the location of the transformer (heat dissipation, accessibility for maintenance, etc.).
Wire Sizing
Properly size all conductors based on the calculated load and applicable codes.
Grounding
Ensure proper grounding of all equipment and the transformer according to the NEC.
In Summary
This is a complex situation that requires careful planning and execution. Get the rectifier voltage information. Perform load calculations. Consult with an engineer if necessary. Document everything. Prioritize a 3-phase to 1-phase transformer if possible. Good luck! Flag for review