User: lastminutepanic, Location: Long Island, NY
Asked on: Friday, November 15, 2024 at 5:06 pm EST
Answered on: Thursday, March 6, 2025 at 5:17 am EST
Question: I'm installing a new meter pan and exterior main panel at a client's house in preparation for an upcoming solar install. The new meter pan is required by the solar company because of the poor (rusty) state of the existing conduit and pan. I'm putting in an exterior main panel to provide an exterior service disconnect, and because it's convenient for future electrical work I'll be doing for him. Since I'm doing this work for my client instead of the solar company, I'm in contact with their people to make sure my install meets their needs.I tell my contact that I plan to place the exterior panel so that the bottom is 20" from the ground, which will put the main breaker lever about 34" from ground level. He tells me that the main breaker lever has to be 3.5ft minimum to ground. I know about the 6ft7in maximum, but not a minimum (other than common sense for rain/snow). I call him back and ask him for the article number to make sure I understand the reg, and he says it's in 380.8a and it says 4.5ft, then a few sentences later he says 4ft (it was 3.5ft in the last conversation). I'm thinking, is he talking about 380.8A from the 1999 NEC that's now 404.8A? That still doesn't have a minimum height.Does anyone know what he's talking about? Is there a minimum breaker lever height for exterior panels or service disconnects? I can work around even a 4.5ft minimum, but it's a design/parts change from what I had planned, which is to use an internal knockout to feed conduit directly into an inside-the-house panel. Not a big deal to put the panel higher, come down out the bottom, and LB into the house, but if it's unnecessary I have no reason to. I'd prefer the cleanliness of basically back to back panels and a short piece of conduit through the wall between them.Thanks!
You are correct in your analysis. There is no minimum height requirement for the operating handle of a service disconnect per the NEC, other than what is driven by common sense.Here's a breakdown: NEC 404.8(A) (formerly 380.8(A)) - Accessibility and Grouping
This section primarily addresses the maximum height: "Switch operating handle shall be located no more than 2.0 m (6 ft 7 in.) above the floor or working platform." It also addresses grouping and accessibility, ensuring switches are accessible and grouped conveniently. This can often be confused as minimum height
No Explicit Minimum Height
The NEC does not specify a minimum height for the operating handle of a service disconnect.
Why the Confusion? Local Amendments
It's possible the solar contact is referencing a local amendment to the NEC in their jurisdiction. Local authorities can add or modify requirements. You need to check with your local electrical inspector or building department to see if such an amendment exists in your area.
Utility Requirements
The electric utility may have specific requirements for the height of the service disconnect. While not technically part of the NEC, these requirements are often mandatory for connecting to their grid. Check with your utility company.
Misinterpretation
The contact may be misinterpreting the code or confusing it with other requirements (like ADA accessibility requirements, which don't typically apply to service disconnects on private residences).
"Rules of Thumb"
Some electricians develop rules of thumb based on experience and best practices. 3.5 to 4.5 feet might be a common height they use for ease of operation and accessibility, but that's not an NEC requirement.
What to Do
Confirm with Local Authority
The most crucial step is to contact your local electrical inspector or building department. Ask them specifically if there are any minimum height requirements for service disconnects in your jurisdiction.2.
Check with the Utility
Even if the local authority doesn't have a minimum, the utility might. Call them and ask about their requirements for service disconnect height.3.
Document Everything
Keep records of your conversations with the solar contact, the local inspector, and the utility company. This documentation will be valuable if any questions arise later.4.
Explain to the Solar Contact
Once you have confirmed the actual requirements (or lack thereof), politely explain the situation to the solar contact. Emphasize that you are following the NEC and all local/utility requirements.
Your Original Plan
Your initial plan of having a short conduit run between the exterior and interior panels is generally acceptable and a clean install, assuming it meets all other code requirements (e.g., proper conduit fill, secure connections, etc.).
*In Summary: The solar contact is likely mistaken or referencing requirements that don't apply to your situation. Verify with your local electrical inspector and the utility company to get the definitive answer. Don't change your plan unnecessarily until you have confirmed a specific minimum height requirement. Flag for review