Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Exposed conductor - how to guard it

User: njose424, Location: Carmel, IN

Asked on: Monday, November 18, 2024 at 2:44 pm EST
Answered on: Thursday, March 6, 2025 at 5:21 am EST

Question: Safety newb here trying to improve safety in general industry for my employer.The general rule of thumb here is that if you break the plane of a panel containing 480VAC exposed conductors, you need to have appropriate shock hazard ppe (arc flash is irrelevant to this scenario - please ignore). I'm trying to dig a little deeper here....An exposed conductor doesn't give me enough to go off of for applying that practically. I noticed that inside control panels a lot of the wire contacts where they land in a device, attached with a screw, and the screws are recessed so that you can't access with a finger tip. Is this considered guarded? Exampe from google search below.

You're right to dig deeper! The rule of thumb about crossing the plane of a panel isn't always a perfect indicator, and understanding the concept of "guarded" is key.

Is the Example You Provided "Guarded?"

In most cases, the recessed screw terminals you described and showed in the image would be considered guarded. Here's why: Prevention of Accidental Contact

The recessed design, where the screw head is below the surface of the surrounding material, prevents accidental contact with a fingertip or other body part.


Insulation/Isolation

While the screw itself might be conductive, the surrounding material of the terminal block is typically made of insulating material, further reducing the risk of shock.

Intentional Design

These types of terminal blocks are specifically designed to protect workers from hazards.

How to Determine if Something is "Guarded" (Beyond Just Recessed Screws)

The official definition of "guarded" can vary slightly depending on the specific standard you're following (OSHA, NFPA 70E, etc.), but the general concept is consistent.


OSHA 1910.303(g)(1)(i) (Guarding of Live Parts)

"Except as required or permitted elsewhere in this subpart, live parts of electric equipment operating at 50 volts or more shall be guarded against accidental contact by approved cabinets or other forms of approved enclosures, or by any of the following means: (i) By location in a room, vault, or similar enclosure that is accessible only to qualified persons; (ii) By permanent, substantial partitions or screens so arranged that only qualified persons will have access to the space within reach of the live parts. Any openings in such partitions or screens shall be so sized and located that persons are not likely to come into accidental contact with the live parts; (iii) By location on a suitable elevation to prevent contact; or (iv) By insulation."

Key Considerations for Determining "Guarded" vs. "Exposed"


Accessibility



Can a person easily make accidental contact with the live parts?
If the answer is yes, it's likely not guarded. Is there a physical barrier in place? This could be a recessed design, a cover, insulation, or other means of physical protection.2. Insulation



Is the conductor or terminal surrounded by adequate insulation?
Look for materials rated for the voltage present. Is the insulation in good condition? Cracks, tears, or deterioration can compromise its effectiveness.3. Location



Is the component located in a place where accidental contact is unlikely?
(e.g., high up and out of reach).4. Task at Hand



What work is being performed?
While the screws may be guarded under normal circumstances, if a worker is troubleshooting, and they need to remove the screw to take voltage readings, the hazard may no longer be guarded, and PPE would be required.

Important Caveats and Recommendations



"Qualified Person"

This is a critical term. A "qualified person" has the skills and knowledge related to the construction and operation of the electrical equipment and installations and has received safety training to recognize and avoid the hazards involved. The definition may change between regulations so it is important to verify. Someone who is
not qualified should never be working near potentially exposed live parts.

Specific Standards

Consult the specific electrical safety standards relevant to your industry and location. NFPA 70E (Standard for Electrical Safety in the Workplace) is a widely used standard in the US, but OSHA regulations are the enforceable law.

Written Program

Have a written electrical safety program that addresses the specific hazards in your workplace, defines "qualified person," and outlines required PPE.


Training

Ensure that workers are properly trained on electrical safety, hazard recognition, and the use of PPE.

Risk Assessment

Conduct a thorough risk assessment of each task involving electrical equipment to determine the appropriate level of PPE and safe work practices. This assessment should take into account potential arc flash hazards
and shock hazards.

De-energize First

Always de-energize equipment before working on it whenever possible. This is the safest approach.

Lockout/Tagout

Implement a robust lockout/tagout procedure to ensure equipment remains de-energized during maintenance or repair.


Clear Labeling

Ensure panels are clearly labeled with voltage levels and any potential hazards.

In Summary:


While recessed screw terminals are often considered "guarded" against accidental contact, it's essential to assess the specific situation, consider the task being performed, and consult relevant safety standards to make a definitive determination. Never assume something is safe without proper evaluation. Invest in training, implement a written safety program, and prioritize de-energizing equipment whenever possible. Flag for review

Previous Question Next Question