Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: 4-Position Load break Switch for Pad- Mounted Transformer Loop Feed

User: faresos, Location: New York, 40.7514,-73.9925

Asked on: Wednesday, November 20, 2024 at 10:52 am EST
Answered on: Thursday, March 6, 2025 at 5:27 am EST

Question: Hello Everyone,I'm reviewing a spec for this transformer and it appears there are option for the configuration of the switch will let it to operate and allow for A & B sides to be paralleled and connected to the transformer. The current design calls out this transformer will receive two power sources from two separate buses upstream. The confusing part, this seems to be similar to closed transition concept which we need to avoid due to a lot of issues we will have to deal with. What is exactly the intent of this configuration and where it can be used. Our intent is only to have a manual selection between the two sources at the transformer primary section.Thank you!

Okay, let's break down the potential intentions behind the transformer configuration you're describing and compare it to your desired outcome of simple manual source selection.

Understanding the Possible Configuration

The spec describing the transformer switch allowing A & B sides to be paralleled suggests a configuration aimed at increasing reliability, capacity, or both. Here's what likely happening or what they are trying to do:

Paralleling Power Sources

This suggests that both sources (A and B) can be connected to the transformer simultaneously. The transformer winding likely have dual primary windings. This is where the "paralleling" comes in. The switch configuration is likely designed to connect the two sources to these parallel windings.


Potential Intentions Behind Parallel Operation



Increased Capacity

If the transformer is sized to handle the combined capacity of both sources, paralleling allows you to draw more power than either source could provide individually.


Increased Reliability (Redundancy)

If one source fails, the other source can continue to power the load (albeit potentially at a reduced capacity). This assumes the transformer is appropriately sized for the load even with only one source.

Load Balancing

Paralleling can potentially balance the load between the two sources, assuming they have slightly different voltage characteristics or impedance.


'Soft' Transfers (Likely the Root of the Closed Transition Concern)

If the switch is designed to close the connection between the sources before opening the connection to the other source, you're effectively paralleling them momentarily. This is the closed transition concept.

Why the Closed Transition Concern is Valid

Closed transition switching (make-before-break) poses significant problems, especially with unsynchronized or dissimilar power sources:

Circulating Currents

When two unsynchronized sources are momentarily paralleled, significant circulating currents can flow between them. These currents stress the transformer windings, switchgear, and upstream equipment.


Voltage Dips/Surges

The act of momentarily paralleling can cause voltage dips or surges that can disrupt sensitive equipment.

Protection Coordination Challenges

Closed transition switching complicates protection coordination. Faults during the transition period can be difficult to detect and clear quickly.


Source Instability

One source can potentially destabilize the other if there's a significant difference in their characteristics.

Not Always Allowed

Utility interconnections often forbid closed transition transfers unless specifically approved and carefully engineered.

Why This Might Not Be What You Want (Given Your Requirements)

You stated that your intent is only to have a
manual selection between the two sources at the transformer primary. If that's truly the case, a paralleling capability, especially with a closed transition switch, is unnecessary and introduces potential problems.

How This Configuration Might Still Be Useful (But Probably Isn't in Your Case)

Even if your goal is mainly manual selection between the two sources, there may be a few situations where a paralleling option could be beneficial - under the condition you have no issue in paralleling two independent power sources.


Short Period, Low Load Paralleling During Transfer

If you can guarantee the sources are synchronized (e.g., via a sync-check relay) and the load during the paralleling period is light, you might be able to tolerate short paralleling periods. However, this requires careful analysis and control.

Maintenance

If you need to be able to quickly and efficiently transfer between sources during maintenance, and if a sync-check relay is in place, the ability to parallel the sources may prove useful.

Recommendations and Questions to Ask


Clarify the Switch Operation

The most important step is to get
precise details about the switch's operation. Ask the vendor:

Is it truly capable of closed transition?
(Make sure the "paralleling" configuration doesn't require closed transition.) What is the intended use case for the paralleling configuration? Is the switch capable of "break-before-make" operation? (This is what you want for a simple manual selection.) Are any special settings or devices required to avoid closed transition (e.g., sync-check relays, time delays)? What are the switch's interrupting and withstand ratings for parallel operation? (This is important if it's a true closed transition setup.)2. Review the Transformer Windings

Is the transformer designed for parallel operation of primary windings? If so, understand how the windings are connected.3.

Re-evaluate Your Needs

Are you absolutely sure you only need manual selection? Could there ever be a need for even limited redundancy or load balancing?4.

Consider a Simpler Solution

If manual selection is your primary requirement, you can almost certainly use a simpler transfer switch (e.g., a manual transfer switch, or an automatic transfer switch programmed for open transition) and a standard transformer with single primary. This will be much less complex and less prone to problems.5.

Consult with a Power System Engineer

If there is any confusion at all, especially if there are special conditions such as redundancy, always consult with a power system engineer.

In summary:
The paralleling configuration for the transformer switch suggests a potentially complex setup with a closed transition transfer capability. Since you only need a manual selection between the two sources, it's crucial to confirm the switch can operate in a "break-before-make" mode to avoid the problems associated with paralleling unsynchronized power sources. If that cannot be verified, consider a simpler, more appropriate solution that meets your requirements. Flag for review

Previous Question Next Question