User: Alwayslearningelec, Location: NJ
Asked on: Wednesday, November 20, 2024 at 1:08 pm EST
Answered on: Thursday, March 6, 2025 at 5:27 am EST
Question: When any of you have installed a recessed 4' fixture that required secondary type of support in case fixture/ceiling falls etc. What have you done? Chain or aircraft cable to deck?
You're right to think about secondary support! A recessed 4' fixture falling would be a serious hazard. Here's a breakdown of common methods and considerations
Methods for Secondary Support
Safety Chains
Pros
Simple, inexpensive, readily available, easy to install.
Cons
Can be bulky, potentially more prone to sagging over time (though high-quality chains are quite strong), can be visually less appealing than cable. Need to ensure the chain's load rating is significantly greater than the fixture's weight.
Aircraft Cable (Wire Rope)
Pros
Strong, lightweight, visually cleaner, less prone to sagging. More resistant to corrosion if stainless steel is used.
Cons
Requires specialized tools (crimpers, cable cutters) for proper installation. Slightly more expensive than chain. Crimps must be done correctly, or the cable's strength is compromised.
Specific Fixture Support Kits
Pros
Designed specifically for supporting light fixtures, often with integrated attachment points and adjustable lengths. May meet code requirements more easily.
Cons
Might be more expensive than generic chain or cable. You need to ensure the kit is rated for the weight of your specific fixture.
Key Considerations and Steps
Code Requirements
Always check your local electrical codes and building codes. Many jurisdictions require secondary support for recessed fixtures, especially in commercial settings or where there's a risk of damage or injury if a fixture falls. Some codes specify the type of support allowed.2.
Fixture Weight
Know the exact weight of your fixture. This is critical for selecting the correct chain, cable, or support kit. Add a safety margin (e.g., double the weight).3.
Attachment Points
Fixture
Look for existing attachment points on the fixture housing. Many fixtures have pre-drilled holes or tabs specifically for secondary support. If none exist, do not drill into the fixture without consulting the manufacturer. You could compromise the fixture's integrity or electrical safety.
Structure Above (Deck)
You need a secure attachment point to the structure above the ceiling. Here are some options:
Structural Members (Joists, Beams)
This is the best option. Use appropriate hardware (eye bolts, beam clamps) to attach the chain or cable directly to a structural member.
Suspension System (Drop Ceiling)
Never rely solely on the drop ceiling grid for secondary support. You must attach to the structure above the drop ceiling. Special "drop ceiling support kits" exist that allow you to run cable or chain from the fixture, through the drop ceiling, and up to the joists.
Concrete Deck
Use concrete anchors rated for the load. Make sure they are properly installed.4.
Installation
Chain
Use S-hooks or quick links to connect the chain to the fixture and the support structure. Make sure the hooks are fully closed to prevent accidental disconnections.
Cable
Use the correct crimping tools and follow the manufacturer's instructions. A poorly crimped cable can fail even under light loads. Use thimbles to prevent the cable from kinking at the attachment points.
Slack
Provide a small amount of slack in the secondary support. You want the fixture to be held securely, but you don't want the secondary support to be under constant tension unless the primary support fails. A few inches of slack is usually sufficient.5.
Inspection
After installation, thoroughly inspect the entire system. Make sure all connections are secure and that the secondary support is properly attached. Gently test the system by applying a small amount of downward pressure to the fixture.6.
Documentation
Keep a record of the fixture weight, the type of secondary support used, and the installation date. This can be helpful for future maintenance or inspections.
Example Scenario (Commercial Office with Drop Ceiling)
Code Research
Check local codes.2.
Fixture Weight
The 4' LED fixture weighs 15 lbs.3.
Secondary Support
Choose aircraft cable with a rated load of 50 lbs (more than double the fixture weight).4.
Attachment Points
Fixture
The fixture has pre-drilled holes for safety cables.
Structure Above
Locate the ceiling joists above the drop ceiling.5.
Installation
Install drop ceiling support kits above each fixture location. Run aircraft cable from the fixture, through the drop ceiling support kit, and up to the joist. Use appropriate hardware (eye bolt or beam clamp) to securely attach the cable to the joist. Crimp the cable securely at both ends. Leave a few inches of slack in the cable.6.
Inspection
Thoroughly inspect all connections.7.
Documentation
Keep a record of the installation.
Important Notes
Electrical Safety
Always disconnect power to the circuit before working on any electrical fixture.
Professional Help
If you're not comfortable working with electrical wiring or structural support, hire a qualified electrician or contractor. Incorrect installation can be dangerous.*
Manufacturer's Instructions: Always follow the fixture manufacturer's instructions for installation and secondary support.By carefully considering these factors and following best practices, you can ensure that your recessed fixtures are safely and securely installed. Flag for review