User: elmundogrande, Location: Tennessee
Asked on: Wednesday, November 20, 2024 at 2:53 pm EST
Answered on: Thursday, March 6, 2025 at 5:28 am EST
Question: Let’s say: I have a 30 KVA step-up transformer 240 to 480 volts and no mention of thermal overloads. Using table 450.3B with primary and secondary protection is going to be used 30000/240v= 125A x 250% = 312.5 according to the table I can’t use the next size up not using x125% and no mention of thermal overload so a 300a ocpd is needed.
You're on the right track, but let's break down the calculation and reasoning more clearly to ensure code compliance
Understanding Table 450.3(B)
Table 450.3(B) of the National Electrical Code (NEC) deals with the maximum overcurrent protection allowed for transformers. It offers two main paths: Primary-Only Protection
This is simpler but often results in a larger overcurrent device (OCPD).
Primary and Secondary Protection
This allows for smaller OCPDs, but requires both the primary and secondary to be protected. This is the method you're using.
Your Calculation and Code Considerations
Transformer KVA to Primary Amps
You correctly calculated the primary full-load current (FLC): 30,000 VA / 240 V = 125 A2.
Overcurrent Protection Limit (Table 450.3(B)): Using the "Primary and Secondary Protection" method in Table 450.3(B), and because you have no information suggesting otherwise for transformers rated over 1000 volts you are allowed up to 250% of the primary FLC for the primary overcurrent protection.3. Overcurrent Protection Calculation
125 A x 250% = 312.5 A4.
Standard OCPD Sizes and the "Next Higher Standard Overcurrent Device Rating" Rule
This is where the code gets a bit tricky. NEC 240.4(B) allows you to go to the "next higher standard overcurrent device rating" if the calculated value does not correspond to a standard rating from NEC 240.6(A). Common standard OCPD sizes (from NEC 240.6(A)) include 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 1000, 1200, 1600, 2000, 2500, 3000, 4000, 5000, and 6000 amps. Since 312.5 A does not correspond to a standard OCPD size, you can use the "next higher standard overcurrent device rating" per 240.4(B). Therefore, you can use a
350A OCPDTherefore, you can use a 350A OCPD.Important Considerations
Secondary Protection is Required
Using Table 450.3(B) with primary and secondary protection requires you to have overcurrent protection on the secondary side of the transformer as well. You'll need to calculate the secondary FLC (30,000 VA / 480 V = 62.5 A) and then determine the maximum allowable secondary OCPD size (based on Table 450.3(B) for the secondary side). Typically this is 125% rated. 62.5 x 1.25 = 78.125, you could use a 80 amp OCPD
Conductor Ampacity
Don't forget to ensure that the conductors on both the primary and secondary sides of the transformer are sized according to NEC Article 310 and are adequately protected by the respective OCPDs. You cannot protect undersized conductors with oversized OCPDs.
Coordination
Ideally, your overcurrent protection should be coordinated to minimize unnecessary outages. This involves selecting OCPDs with appropriate time-current characteristics so that smaller overloads are cleared by downstream devices before the transformer primary OCPD trips.
Local Amendments
Always check with your local electrical inspector for any local amendments to the NEC.
Short-Circuit Current Rating
Ensure that all components in the system (including the transformer, OCPDs, conductors, and equipment) have adequate short-circuit current ratings (SCCR).
In summary: Calculate the primary and secondary FLC. Use Table 450.3(B) to determine the maximum allowed OCPD sizes. Apply the "next higher standard overcurrent device rating" rule from 240.4(B) only if the calculated OCPD size is not a standard size from 240.6(A). Ensure the conductors are properly sized and protected. Coordinate the OCPDs. Verify SCCR.* Check with your local inspector.By following these steps, you can ensure a safe and code-compliant transformer installation. Good luck! Flag for review