User: sparkync, Location: North Carolina
Asked on: Thursday, November 21, 2024 at 8:49 am EST
Answered on: Thursday, March 6, 2025 at 5:29 am EST
Question: Just wired for a portable generator to supply power to a dwelling in case of power outage. I've got the "Osha" requirement that it must be connected toa grounded electrode system, such as a ground rod, etc. Since the wiring is 4 wire, and carrying the ground connection back to the service panel, would not the existing ground rod for the house meet this requirement, rather than driving another ground rod at the generator, or is there another requirement in the NEC?Thanks
You've hit on a common point of confusion when setting up a portable generator for backup power. Let's break down the requirements
Understanding the Grounding Concepts
Separately Derived System (SDS)
A portable generator, when not connected to the utility grid, is generally considered a Separately Derived System (SDS). This means it's acting as its own source of power, isolated from the utility.
Non-Separately Derived System
When the generator is powering loads through the main service panel, the generator is acting as a Non-Separately Derived System.
OSHA's Requirement (and NEC's influence)
OSHA typically requires generators used on construction sites or for temporary power to be grounded. The reasoning behind this is to provide a path for fault current to flow in case of an equipment failure, helping to trip a breaker and prevent electrocution.The NEC (National Electrical Code) provides more specific guidance on grounding for generators, and OSHA will defer to the NEC.
The Key: Switching and Interconnection Transfer Switch is Key
The critical factor is how you're connecting the generator to your house. You must use a transfer switch (either manual or automatic). The transfer switch isolates the generator from the utility grid.
Never backfeed power into the grid by plugging a generator directly into an outlet! This is extremely dangerous. 4-Wire System with Existing Ground
Since you wired a 4-wire system (hot, hot, neutral, ground) from the generator to the transfer switch and back to your main panel, the grounding question depends on how the transfer switch is set up.
The Options and Grounding Requirements
Here's where things get nuanced:1. Transfer Switch with Switched Neutral
Description
Some transfer switches switch both hot wires and the neutral.
Grounding Requirement
In this case, the generator is acting as a Separately Derived System (SDS) when running. Typically, the generator should have its frame bonded to the neutral conductor at the generator itself and the transfer switch neutral should be switched so the neutral is only connected at one point. You need to have the generator neutral bonded to the frame on the generator for it to be safe.
Advantages
Provides the best protection against ground faults when operating on generator power.
NEC Section
Relevant sections of the NEC are 250.30 and 250.
35.2.
Transfer Switch that Does NOT Switch Neutral
Description
This type of transfer switch only switches the hot wires. The neutral conductor remains continuously connected to the main service panel neutral.
Grounding Requirement
In this case, the generator is acting as a Non-Separately Derived System. The generator does not have its frame bonded to the neutral conductor. The existing grounding electrode system (your ground rod at the main panel) is sufficient because the neutral is always bonded to ground at the service entrance. This relies on the grounding conductor in your 4-wire feed back to the panel to provide the ground fault path. The bonding must happen back at the main service panel, so the generator must not have its neutral bonded to the frame.
Advantages
Simpler wiring.
NEC Section
Relevant section of the NEC is 250.34.
Important Considerations and Best Practices
Consult a Qualified Electrician
This is not a DIY situation if you're unsure. Incorrect wiring can be dangerous and violate electrical codes. A licensed electrician can inspect your setup and ensure it's safe and compliant.
Read the Transfer Switch Instructions
The manufacturer's instructions for your specific transfer switch are critical. They will detail the correct wiring and grounding procedures.
Generator Instructions
Consult the generator's documentation as well, especially regarding neutral bonding.
Bonding Jumper
Many portable generators have a removable bonding jumper that connects the neutral terminal to the generator frame. You need to know whether this jumper is present and how to remove or install it depending on your transfer switch setup.
GFCI Protection
If the generator supplies 125-volt, 15-, 20-, and 30-ampere receptacles, these receptacles must be GFCI-protected (NEC 445.9). Many generators have GFCI outlets built-in.
Permits and Inspections
Check with your local building department to see if a permit and inspection are required for your generator installation.
In Summary
If you are using a transfer switch that switches the neutral, you will need to ensure that the generator's neutral is bonded to the frame and that you have a grounding electrode system at the generator. If your transfer switch does not switch the neutral, your existing ground rod at the main panel is sufficient, but the neutral should not be bonded to the frame at the generator. Always consult a qualified electrician to verify the correct and safe configuration for your specific setup. Flag for review