Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Demo

User: Alwayslearningelec, Location: NJ

Asked on: Thursday, November 21, 2024 at 10:10 am EST
Answered on: Thursday, March 6, 2025 at 5:30 am EST

Question: We have work in a few bathrooms like this that are within a college so the floor footprint is large.They are gutting the room and we’re installing new receptacles, lights, fire alarm etc.They want us to connect all new work to existing circuits made availabe after demo.A few questions.How would you keep the fire alarm system active regarding the existing wiring when demo happens.I’m sure there are adjacent areas that are feed from same circuit that feed the bathroom. In that case what would the approach be? Trace circuits, then modify the circuit to keep adjacent area active but somehow de-energize power to demo area? What would be best way to approach this? Think adjacent area would have to be temp'ed out of fed from same circuit as restrooms?Thanks

Okay, this is a common situation in renovations, and it requires careful planning and communication to minimize disruption and maintain safety. Here's a breakdown of how to approach it, focusing on the fire alarm system and the general circuit management.1. Fire Alarm System Integrity During Demolition

This is critical. You cannot simply disconnect fire alarm circuits without a plan and proper approvals. Failure to do so can compromise the entire fire safety system of the building and potentially violate fire codes. First and Foremost: Engage the Fire Alarm Company AND the Authority Having Jurisdiction (AHJ): Before any work begins on the fire alarm system, contact the company that services and maintains the fire alarm system for the college and the local fire marshal or building inspector (the AHJ). They need to be involved in the planning. Explain the scope of the work and your need to disconnect/re-route/modify existing fire alarm circuits. They will dictate the approved methods and necessary procedures. Get everything in writing. They may want a licensed fire alarm technician to be the one doing the cutting/tying of the alarm circuit Possible Scenarios and Solutions (depending on the system and AHJ requirements)



Complete System Shutdown (Least Desirable)

If the affected fire alarm circuits cannot be isolated without impacting a large portion of the system, a complete system shutdown
may be necessary. This requires: Advanced Notification: All building occupants, the campus security, and the fire department must be notified well in advance of the shutdown. Fire Watch: A fire watch (usually trained personnel continuously patrolling the affected areas, looking for signs of fire) must be implemented during the entire shutdown period. The AHJ will dictate the requirements for the fire watch (frequency of patrols, required equipment, etc.). Rapid Re-activation: The system must be brought back online as quickly as possible.

Temporary System Modifications (More Common)

This is usually the preferred method. The fire alarm company, working under your supervision, will:
Identify Affected Devices: Determine which devices (smoke detectors, pull stations, horns, strobes) are on the circuits you need to work with. Temporary Re-routing: They might temporarily re-route the circuits to bypass the demolition area, keeping the rest of the system active. This usually involves carefully disconnecting the affected devices and connecting them to temporary wiring or a temporary panel. Temporary Device Relocation: In some cases, they might relocate devices within the bathroom to avoid damage during demolition. Isolation Modules: Use addressable modules designed to isolate sections of fire alarm circuit without tripping the entire zone. This may require new or existing panel programming.

System Programming Modifications (Often Necessary)

The fire alarm system programming may need to be temporarily modified to reflect the changes in circuit configuration. This should only be done by a qualified and licensed fire alarm technician.

Documentation

Thoroughly document
everything. Keep records of all modifications, shutdowns, fire watch logs, and approvals from the fire alarm company and the AHJ.

2. Managing Existing Circuits During Demolition


This is a more general electrical issue, but still requires careful planning:
Circuit Identification and Tracing (The Foundation)

Thoroughly Map Existing Circuits: Before any demolition begins, carefully trace and map all existing circuits in the bathroom and adjacent areas. Use a circuit tracer/breaker finder (tone generator) to positively identify each circuit breaker and what it feeds. Document this in detail, including the location of all outlets, lights, and other devices on each circuit. Include the wire size. Confirm Voltages: Verify the voltage of each circuit (120V, 208V, etc.) before working on it. Lockout/Tagout: Always follow proper lockout/tagout procedures before working on any electrical circuit. Verify the circuit is de-energized before touching any wires.

Keeping Adjacent Areas Active While Isolating the Bathroom

Ideal Scenario: Dedicated Circuits for the Bathroom: If the bathroom has dedicated circuits that do not feed adjacent areas, the solution is simple: de-energize and disconnect those circuits at the panel after properly identifying them. Clearly label the breakers as "Bathroom Renovation - DO NOT ENERGIZE." More Common Scenario: Shared Circuits: This is more likely, and requires more planning: Identify the Splice Point: Determine where the circuit splits to feed both the bathroom and the adjacent area. This is often in a junction box near the bathroom entrance. Modify the Junction Box: After de-energizing the circuit: Disconnect the wiring leading into the bathroom. Cap off the wires securely with wire nuts and electrical tape. Label them clearly: "Bathroom Renovation - Disconnected." Re-connect the wiring that feeds the adjacent area, ensuring the connection is sound and secure. Avoid Wire Nuts Inside the Panel: Do not modify anything inside the panel unless absolutely necessary. Splices inside the panel introduce points of failure and can make future troubleshooting more difficult. Temporary Power (If Necessary): If modifying the circuit to isolate the bathroom will interrupt power to critical areas in the adjacent space, consider providing temporary power. This could involve: Running a temporary circuit from a different panel: Use appropriately sized wiring and breakers. Using a generator: Make sure it's properly grounded and connected to a transfer switch (if required by code).

Documentation (Again, Crucial)

Update your circuit maps to reflect any modifications you've made. Document the location of any junction boxes where circuits were modified. Take photos of the wiring before and after modifications.

Important Considerations and Best Practices



Communication is Key

Communicate regularly with the college's facilities department, the fire alarm company, and the AHJ. Keep them informed of your progress and any potential problems.


Code Compliance

Ensure all work complies with the National Electrical Code (NEC) and any local codes.

Safety First

Prioritize safety at all times. Use proper PPE, follow lockout/tagout procedures, and be aware of potential hazards.


Minimizing Disruption

Plan your work to minimize disruption to the college's operations. Schedule noisy or disruptive tasks during off-peak hours.

Professionalism

Maintain a professional attitude and treat the college's property with respect.

In Summary


Fire Alarm System

Engage the fire alarm company and the AHJ
first*. They will dictate the approved methods for maintaining fire alarm system integrity.2.

Circuit Management

Thoroughly map and trace existing circuits. Identify the splice point between the bathroom and adjacent areas. Modify the circuit to isolate the bathroom, while keeping the adjacent areas powered. Provide temporary power if necessary.3.

Documentation

Document everything. Update circuit maps, take photos, and keep records of all approvals and modifications.4.

Communication:
Communicate regularly with the college's facilities department, the fire alarm company, and the AHJ.This is a complex task, and it's important to have the necessary skills and experience to do it safely and correctly. If you're not comfortable with any of these procedures, consult with a qualified electrician or fire alarm technician. Flag for review

Previous Question Next Question