Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: EGC Sizing

User: Therealcrt, Location: Kansas City

Asked on: Thursday, November 21, 2024 at 10:20 am EST
Answered on: Thursday, March 6, 2025 at 5:31 am EST

Question: 20 amp circuit 120 V it’s roughly 350 to 400 feet from the panel. I’m upsizing the hots to number 4 copper to accommodate Voltage Drop I know I need to upsize my equipment grounding conductor as well. Do I first see what number 4 copper amps city is rated for then go back to table 250.122 and adjust equipment grounding conductor based off of that amperage.? Which would be 85 A for number4 and the minimum size equipment grounding conductor would be number 8 copper?

You're on the right track with upsizing the EGC due to upsizing the ungrounded conductors for voltage drop. Let's break down the process and verify your assumptions

Understanding the NEC and the Goal
Voltage Drop

The primary reason for upsizing the ungrounded conductors.


Equipment Grounding Conductor (EGC)

Its primary function is to provide a low-impedance path for fault current back to the source (panel) to facilitate the operation of the overcurrent protective device (circuit breaker) in the event of a ground fault.

NEC 250.122

This table dictates the
minimum size of the EGC based on the rating of the overcurrent device protecting the circuit. However, it also contains instructions for upsizing the EGC when the ungrounded conductors are increased in size.

Steps for Determining the EGC Size
1. Start with the Overcurrent Device

Your circuit has a 20A breaker. NEC 250.122 requires a

#12 AWG copper
EGC for a 20A circuit.2. Upgrownded Conductor Upsizing and NEC 250.122(B)

Since you upsized the ungrounded conductors, you must also increase the size of the EGC proportionately. The NEC is specific on this requirement:


250.122(B): Increase in Size.
Where ungrounded conductors are increased in size from the minimum size that has sufficient ampacity for the intended installation, wire-type equipment grounding conductors shall be increased in size proportionately according to the circular mil area of the ungrounded conductors.3. Calculate the Proportionate Increase



Area Calculation is key here

The relative size difference between your originally required conductor, and your upgraded conductor has to be known.
First, we need to know the circular mil area of the originally required wire for a 20A circuit: #12 AWG Copper: 6,530 circular mils (approximate). Second, we need to know the circular mil area of the new, upsized wire. #4 AWG Copper: 41,740 circular mils (approximate). Calculate the ratio: 41,740 / 6,530 = 6.39 Multiply the circular mil area of the minimum EGC by the ratio: 6.39 This doesn't help us much as we are already using a wire that is much larger. We need to calculate the new ciruclar mil size of the EGC required. Multiply the circular mil area of the 12AWG EGC by the ratio of 6.39: 6,530 6.39 = 41,726 circular mils Find the conductor size that has a circular mil area equal to or greater than 41,726 circular mils. Based on common wire sizes, #4 AWG copper is the minimum size.

Therefore, you would need a #4 AWG copper EGC.
Important Considerations



NEC 250.122(B) is specific

The EGC must be increased proportionately to the
circular mil area of the ungrounded conductors, not directly based on ampacity.

This is a minimum

You can always use a larger EGC if desired.

Disclaimer:
* I am an AI and cannot provide electrical advice. Consult with a qualified electrician for all electrical installations. Local codes and regulations may vary and must be followed. Electrical work is dangerous and should only be performed by qualified individuals. The information provided here is for educational purposes only and should not be used as a substitute for professional advice. Flag for review

Previous Question Next Question