Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Machine Safety requirement for Filter presses

User: mehdi1351, Location: New Zealand

Asked on: Thursday, November 21, 2024 at 7:21 pm EST
Answered on: Thursday, March 6, 2025 at 5:32 am EST

Question: Hello all,As I am not familiar with US compliance requirement for the machine safety, would appreciate if anyone can assist me on the following:1- Does an E-stop button on the local control panel is enough to stop the machine or should we install a pull-cord or Trip-wire on the both side of filter press and link it into the PLC to stop the machine?2- Does movable guards required on the hydraulic power pack? Currently many manufacturer doesn't propose any movable guards interlock to the filter-press closed limit switch. The safety concern is, when the filter-press closed (under high pressure hydraulic) and if someone release the hydraulic lever (i.e open the filter press), then the high pressure liquid can splash and make a safety concern for someone nearby the device.3- Generally is there any standard I should comply with for machine safety in US?

Okay, let's break down US machine safety compliance for your filter press, focusing on E-stops, guarding, and relevant standards.1. Emergency Stop (E-Stop) Devices The Short Answer

An E-stop button on the local control panel
might be enough, but likely not. A combination of devices, including pull-cords/tripwires, is usually the better approach for a machine like a filter press.

The Reasoning



Risk Assessment is Key

The determination of the necessary safety devices depends on a thorough risk assessment of your filter press operation. This assessment should identify all potential hazards and the level of risk associated with each. Ask yourself: "What are the reasonably foreseeable ways someone could get injured interacting with this machine?"


E-stop Function

The purpose of an E-stop is to provide a readily accessible means to stop the machine quickly in the event of an emergency. The problem with only having an E-stop on the control panel is that someone who needs to stop the machine may not be able to reach the control panel in time.

Pull Cords/Tripwires

These provide a more accessible means of stopping the machine from various locations around the perimeter, particularly along the sides of the filter press. If someone sees an unsafe condition (e.g., someone's hand getting caught, a spill, a mechanical failure), they can act
immediately to stop the machine.

PLC Integration

You are correct to consider integrating the pull-cords/tripwires into the PLC's safety circuit. This ensures a reliable and controlled shutdown of the machine. The E-stop and pull-cords should be wired into a safety relay or safety PLC that is designed to monitor the state of the devices and initiate a safe stop of the machine when a fault is detected.

"Reasonably Foreseeable Use"

OSHA (Occupational Safety and Health Administration) looks at what's "reasonably foreseeable use." If it's reasonably foreseeable that someone might need to stop the machine from a location other than the control panel, then additional E-stop devices are required.


Recommendation



A risk assessment will likely indicate the need for pull cords or tripwires along the sides of the filter press.
Think about the operator's movements, potential pinch points, and areas where an emergency stop might be needed immediately.2. Movable Guards on the Hydraulic Power Pack The Short Answer

Yes, movable guards are
likely required for the hydraulic power pack, especially if there's a risk of high-pressure fluid release.

The Reasoning



Hydraulic Injection Hazard

High-pressure hydraulic fluid injection is a
serious hazard. It can cause severe tissue damage, even with small amounts of fluid.

Lack of Interlocks is Concerning

The fact that manufacturers often don't include interlocks on the guards and the filter-press closed limit switch is a red flag. It suggests a potential safety gap.

Guard Function

The purpose of the guard is to prevent access to the hydraulic components while they are pressurized. An interlock ensures that the machine cannot operate while the guard is open, or that the system is de-pressurized when the guard is opened. This addresses the hazard of accidental release during operation or maintenance.


Mitigation Measures

The risk assessment should consider:

Pressure Relief

Can the hydraulic system be designed to relieve pressure automatically when the guard is opened?


Fluid Containment

Are there measures to contain any potential fluid leaks or bursts?

Guard Design

Is the guard robust enough to withstand a potential hydraulic failure? Is it designed to prevent access to the components while they are under pressure?


Recommendation



You should definitely have movable guards on the hydraulic power pack, and they should be interlocked with the system.
This interlock should prevent operation while the guard is open and ideally depressurize the system when the guard is opened. If you are working with the original manufacturer, strongly recommend to interlock the hydraulic power pack.3. Relevant US Machine Safety Standards OSHA (Occupational Safety and Health Administration)

This is the primary regulatory body for workplace safety in the US. You
must comply with OSHA regulations.

29 CFR 1910 Subpart O - Machinery and Machine Guarding

This is the most important OSHA standard for machine safety. It covers general requirements for guarding machinery to protect employees from hazards such as point of operation, ingoing nip points, rotating parts, and flying chips.

29 CFR 1910.212 - General requirements for all machines

This section outlines general guarding requirements and emphasizes the employer's responsibility to protect employees from machine hazards. It specifically mentions the need for guarding points of operation, rotating parts, and other machine hazards.


29 CFR 1910.147 - The control of hazardous energy (lockout/tagout)

This standard addresses the control of hazardous energy during servicing and maintenance of machines and equipment. While not directly related to normal operation, it's crucial for safe maintenance procedures. Hydraulic energy is definitely considered a hazardous energy source.

ANSI (American National Standards Institute)

ANSI standards are
voluntary consensus standards, but they are widely recognized and often used as best practices. Following ANSI standards can help you demonstrate due diligence in providing a safe workplace. OSHA often references ANSI standards as "recognized" and "generally accepted" safety practices.

ANSI B11 Series

The B11 series covers a wide range of machine tools and equipment. Look for standards relevant to your specific filter press type and hydraulic systems. Specific standards relevant to hydraulic systems within filter presses may not exist, but general ANSI B11 standards provide a framework for risk assessment and hazard mitigation.



NFPA (National Fire Protection Association)

NFPA standards are primarily focused on fire safety, but they can be relevant to machine safety, particularly when electrical systems are involved.


NFPA 79 - Electrical Standard for Industrial Machinery

This standard covers the electrical safety aspects of industrial machinery, including control circuits, wiring, and grounding.

ISO (International Organization for Standardization)

While ISO standards are international, they are increasingly adopted or referenced in the US.


ISO 13849-1 - Safety-related parts of control systems

This standard provides guidance on the design and implementation of safety-related control systems, including those used for E-stops and safety interlocks.

ISO 4413 - Hydraulic Fluid Power – General Rules and Safety Requirements for Systems and Their Components

While perhaps not strictly mandated, this provides good design guidance for hydraulic system safety.

Key Steps to Compliance


Conduct a Thorough Risk Assessment

This is the
most important step. Identify all potential hazards, assess the level of risk, and determine the necessary safety measures. This should be performed by a qualified person.2.

Implement Appropriate Guarding and Safety Devices

Based on the risk assessment, install appropriate guards, interlocks, E-stops, pull cords/tripwires, and other safety devices.3.

Document Everything

Keep detailed records of your risk assessment, safety measures, and any modifications to the machine.4.

Train Employees

Ensure that all employees who operate or maintain the filter press are properly trained on its safe operation, the location and function of safety devices, and emergency procedures.5.

Regular Inspections and Maintenance

Regularly inspect and maintain the filter press and its safety devices to ensure they are functioning properly.

Important Considerations



"Qualified Person"

OSHA often uses the term "qualified person." This means someone with the necessary training, knowledge, and experience to perform a specific task safely. For complex tasks like risk assessments and designing safety systems, it's best to consult with a qualified safety professional or a machine safety expert.

State-Specific Regulations

Some states have their own OSHA-approved state plans that may have additional or more stringent requirements. Check your state's regulations.


Manufacturer's Recommendations

Consult the filter press manufacturer's documentation for any specific safety recommendations or requirements.

In summary: You need to perform a risk assessment to determine the appropriate safety measures for your filter press. E-stops on the control panel alone are likely not sufficient. Movable guards with interlocks are highly recommended for the hydraulic power pack. Comply with OSHA regulations, and consider ANSI and ISO standards for best practices. Good luck! Flag for review

Previous Question Next Question