Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: NEC 240.21(b)(1) Load side taps "rating" confusion

User: ryangittens, Location: usa

Asked on: Friday, November 22, 2024 at 10:57 am EST
Answered on: Thursday, March 6, 2025 at 5:33 am EST

Question: I have a plan reviewer stating that the conductors shall be rated not less than the rating of the equipment containing an OCPD.For example, I have a 100A disconnect with 70 fuses and they are requiring the conductors to be rated at 100A. This doesn't seem correct but the way the code is written it can certainly be interpreted that way. Anyone else ever run into this? Is this correct?

You're right, that interpretation is overly strict and not generally the intent of the NEC. While a literal reading could lead to that conclusion, the NEC provides many allowances that demonstrate this is not the intended application of the rule. Here's a breakdown of why the plan reviewer's interpretation is likely incorrect, and how to address it

The Problem with a Literal Interpretation:
Overly Restrictive

This interpretation would force you to use conductors significantly larger and more expensive than necessary in many applications.


Ignores Code Intent

The NEC is about safety. Using larger conductors than required doesn't necessarily increase safety.

Contradicts Other Code Sections

Several sections of the NEC
specifically allow for conductors to be sized based on the load, not just the overcurrent protective device (OCPD) rating.

Why the Plan Reviewer is (Probably) Wrong

The core issue here is the difference between the
rating of the equipment (the disconnect itself) and the ampacity of the OCPD (the fuse).1.

Disconnect Switch Rating vs. OCPD Rating

A 100A disconnect switch is rated to handle up to 100A continuous current safely. However, the
fuses are the actual overcurrent protection. You are using 70A fuses.2.

NEC 240.4(B) and (D): Protection of Conductors

This section generally requires conductors to be protected at their ampacity. However, there are exceptions. If the ampacity of your conductor is rated over 800A, and you are using standard size OCPDs, this rule would make sense. Since you are dealing with much lower sizes, this rule does not likely apply.3.

NEC 240.4(D): Protection of Small Conductors

This is a common exception for smaller conductors. You cannot use a 100A OCPD on a 14 gauge wire.4.

Load Calculation

The NEC emphasizes sizing conductors based on the calculated load. If the connected load is such that 70A protection is adequate, that's what should drive the conductor sizing. If the calculated load is much smaller than 70A, sizing the conductors based on a 100A OCPD would be overkill and unnecessary.5.

Motor Applications (if applicable)

Article 430 provides specific rules for motor circuits, which often allow conductors to be sized based on the motor's full-load current and service factor, not the OCPD rating.

How to Address the Plan Reviewer


Prepare a Detailed Explanation

Don't just say they're wrong. Provide a written explanation referencing the specific NEC sections that support your design.
Clearly state the calculated load. Explain why the 70A fuse is adequate protection for the conductors based on their ampacity and the load. Reference the NEC sections mentioned above (240.4(B) and (D), and any motor circuit rules if applicable). Emphasize that the disconnect is simply the means of disconnect and its rating doesn't dictate the conductor size when the OCPD is rated lower.2.

Provide Calculations

Include load calculations that demonstrate that the 70A protection is sufficient. Show how the conductor ampacity meets or exceeds the required ampacity based on the load.3.

Ask for Clarification

Politely ask the plan reviewer to clarify which specific NEC section they believe requires the conductors to be sized based on the disconnect rating.4.

Escalate if Necessary

If the plan reviewer remains unconvinced after you've provided a clear and code-backed explanation, you may need to escalate the issue to their supervisor or the chief electrical inspector.

Example Argument

"The conductors are sized based on the 70A overcurrent protection provided by the fuses within the 100A disconnect, and in accordance with NEC Article 240.4. The calculated load served by these conductors is X amps, as detailed in the attached load calculation. The conductors have an ampacity of Y amps, which meets the requirements of the NEC and provides adequate protection against overload, per NEC 240.
4. The 100A disconnect switch is used as a disconnecting means, and its rating is simply the maximum current it can safely handle. The actual overcurrent protection is provided by the 70A fuses."


Important Considerations



Continuous Load

If the load is considered continuous (operating for 3 hours or more), remember to apply the 125% factor when calculating the required conductor ampacity and OCPD rating (NEC 210.19(A)(1) and 215.3).*

Local Amendments:
Be aware of any local amendments to the NEC that might affect the interpretation of these rules.In most cases, a well-reasoned explanation backed by code references and calculations should resolve the issue. Good luck! Flag for review

Previous Question Next Question