Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Standby Generators and transfer switches

User: FaradayFF, Location: California

Asked on: Friday, November 22, 2024 at 1:09 pm EST
Answered on: Thursday, March 6, 2025 at 5:33 am EST

Question: Hello,Is it industry standard to specify a generator with its corresponding brand transfer switch? Say Cummins diesel generator with Cummins ATS?Let's say I went with Eaton ATS on Cummins generator, would there be any challenges with programming the ATS and commissioning the system? What about other brands such as Kohler and CAT, do they play nice with Transfer switches made by other brands?Thanks, EE

Yes, it's common practice and often recommended to specify a generator with its corresponding brand transfer switch (e.g., Cummins generator with Cummins ATS). While it's not a strict industry standard in the sense that you must do it, there are good reasons why it's often the preferred approach.Here's a breakdown

Why Generator Brand + ATS Brand is Often Preferred:
Integrated Compatibility

When the generator and ATS are from the same manufacturer, they are designed and tested to work seamlessly together. This includes things like:


Communication Protocols

The generator controller and the ATS controller often have direct communication links using proprietary protocols. This allows for advanced features like generator health monitoring, remote diagnostics, and optimized transfer logic.

Voltage/Frequency Matching

The ATS is pre-configured to match the generator's voltage and frequency output.


Load Management

Some generator/ATS systems allow for load shedding or staged startup of loads to prevent overloading the generator. This is easier to implement with a matched system.

Single Point of Contact for Support

If there are issues, you have one manufacturer to contact for both the generator and ATS, simplifying troubleshooting.


Warranty Considerations

Sometimes using mismatched brands can complicate warranty claims. The generator manufacturer might argue that the ATS caused a problem, or vice versa.

Simplified Programming and Commissioning

Matching brands typically means easier setup and commissioning. The controllers are designed to communicate effectively, and the pre-programmed settings are often optimized for that specific generator.

Challenges with Mismatched Generator/ATS Brands (e.g., Eaton ATS with Cummins Generator)



Communication Issues

This is the biggest potential hurdle. The ATS and generator may use different communication protocols. While you can often find a way to interface them, it may require:

Hardwired Connections

Relying solely on hardwired start/stop signals, voltage sensing, and alarm contacts, which limits functionality.


Protocol Converters

These devices translate between different communication protocols (e.g., Modbus to a proprietary protocol). This adds complexity and another potential point of failure.

Custom Programming

Significant time may be spent custom programming both the ATS and generator controllers to work together correctly. This requires a skilled technician who understands both systems.


Compatibility Issues

Even with communication established, there might be compatibility issues in terms of voltage, frequency, and other parameters. You'll need to carefully verify that the ATS is suitable for the generator's output.

Limited Functionality

You may not be able to take full advantage of the advanced features offered by either the generator or the ATS if they are not designed to communicate effectively.


Complex Troubleshooting

Pinpointing the source of problems becomes more challenging when the generator and ATS are from different manufacturers.

Do Kohler, CAT, and Other Brands "Play Nice" with Transfer Switches Made by Other Brands?


Generally, yes, but with the caveats mentioned above. They can be made to work together, but it will likely involve more effort, potential limitations, and a higher risk of compatibility issues compared to using a matched system. Here's a more nuanced view: Basic Functionality

Ensuring basic functionality (generator start/stop, voltage sensing, transfer of load) is usually achievable with different brands. Hardwired connections can handle this.


Advanced Features

Accessing advanced features like remote monitoring, load shedding, and diagnostics is where you'll likely encounter problems if the brands aren't matched.

When Mismatched Brands Might Be Acceptable



Simple Applications

For very basic backup power systems where you only need the generator to start when the utility fails and transfer the load, a mismatched ATS might be acceptable, especially if cost is a major factor. Even then, thorough testing and compatibility checks are crucial.


Legacy Systems

In some cases, you might have an existing ATS that you want to reuse with a new generator.

Specific Project Requirements

Sometimes a project requires a particular feature or capability that is only offered by a specific ATS manufacturer, even if it's not the same brand as the generator.


Cost Savings

If budget is a significant constraint, using a different brand of ATS can sometimes provide cost savings. However, it's crucial to weigh these savings against the potential risks and increased commissioning costs. Often, the extra labor and potential problems negate the initial savings.

Recommendations


Prioritize Matched Brands

Whenever possible, specify a generator and ATS from the same manufacturer to ensure optimal compatibility, ease of commissioning, and simplified support.2.

If Mismatching, Research Thoroughly

If you must use mismatched brands, conduct extensive research to verify compatibility. Consult with both the generator and ATS manufacturers to understand any potential limitations.3.

Budget for Additional Commissioning

Be prepared to spend more time and money on commissioning when using mismatched brands. Engage experienced technicians who are familiar with both systems.4.

Document Everything

Carefully document all wiring diagrams, communication protocols, and configuration settings to aid in future troubleshooting.5.

Testing, Testing, Testing:
Rigorously test the entire system under various load conditions to ensure it functions correctly.In summary, while it's possible to mix and match generator and ATS brands, it's generally best to stick with a matched system unless there's a compelling reason not to. The potential headaches and limitations often outweigh any cost savings. Flag for review

Previous Question Next Question