Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Resistance on heat trace testing

User: Capsfloyd, Location: Lancaster, Texas , USA

Asked on: Saturday, November 23, 2024 at 3:11 pm EST
Answered on: Thursday, March 6, 2025 at 5:36 am EST

Question: Please explain the resistance using a megger on testing Raychem heat trace , 5 watt , 277 volt20 amp .

Okay, let's break down what you should expect when megger testing Raychem (or similar self-regulating) heat trace cable, and what those readings might indicate, given the specifics you've provided.

Understanding the Setup Raychem (Self-Regulating) Heat Trace

This type of heat trace changes its power output based on the temperature of the pipe or surface it's applied to. It has a semi-conductive core.


5 Watt/Foot

A measure of how much heat the cable puts out per foot at a given temperature (typically a cold temperature, like 40°F or 10°C).

277 Volt

The voltage the heat trace is designed to operate at.


20 Amp

The maximum circuit breaker rating the heat trace should be on. This determines the total length of heat trace you can safely run on one circuit.

Megger (Insulation Resistance Tester)

A device that applies a high DC voltage (typically 500V, 1000V, or higher) to test the insulation resistance of a cable or device.

Expected Megger Readings (and Why They Might Vary)


The purpose of a megger test on heat trace is to verify the integrity of the insulation
before energizing the system. You are looking for leakage current, indicating the insulation has been compromised somewhere. Ideal Scenario (Excellent Insulation)

A very high resistance reading. You want to see megohms (millions of ohms) or even higher (hundreds or thousands of megohms). Ideally, you'd see something like ">>2000 MΩ" (much greater than 2000 megohms, which is often the upper limit of the megger).

Acceptable Scenario (Good Insulation)

A reading in the
high megohm range. Let's say 500 MΩ to 2000 MΩ. This generally indicates the insulation is in good condition and safe to energize.

Questionable Scenario (Marginal Insulation)

Readings in the low megohm range (10 MΩ to 500 MΩ) should be investigated. This could indicate moisture ingress, physical damage to the cable, or general degradation of the insulation. Do not energize the cable until the cause of the low reading is found and corrected.

Unacceptable Scenario (Poor Insulation)

Readings
below 10 MΩ are definitely unacceptable. This indicates a significant insulation fault, posing a shock hazard and a risk of equipment damage. Do not energize the cable. The cable must be repaired or replaced.

Factors Affecting Readings


Several factors can influence the megger readings you get on heat trace:1. Temperature

Insulation resistance
decreases with increasing temperature. A cold cable will typically show a higher resistance than a warm cable. Try to test at a consistent ambient temperature.2.

Moisture

Moisture is the
enemy of electrical insulation. Moisture significantly lowers insulation resistance. If the heat trace has been exposed to rain, snow, condensation, or has been buried in wet insulation, you will likely see a lower reading.3.

Length of Heat Trace

The longer the run of heat trace, the
lower the overall insulation resistance will be. This is because any small amount of leakage current is multiplied over the entire length of the cable.4.

Age of the Cable

Insulation degrades over time due to heat, UV exposure, chemical exposure, and general wear and tear. Older heat trace will often have lower insulation resistance than new cable.5.

Voltage Used for Megger Test

The voltage used can effect the readings. If you do not know the correct voltage to use for the megger test, use 500 volts to start.6.

Type of insulation

Different materials provide different levels of insulation. The cable manufacturer will provide expected resistance readings.7.

Contamination

Chemicals can break down insulation.

How to Perform the Megger Test
1. Safety First!



De-energize and Lockout/Tagout

Ensure the heat trace circuit is completely de-energized at the breaker and that a proper lockout/tagout procedure is followed. This is critical for safety.

Disconnect

Disconnect the heat trace cable from the power supply at the junction box. This isolates the cable for testing.
Make sure you disconnect both the line and neutral wires.

Wear Appropriate PPE

Wear insulated gloves and safety glasses.2.

Megger Connections



Line to Ground

Connect one lead of the megger to one of the conductors (typically the black or red wire). Connect the other lead of the megger to the
ground (the green wire or the metallic conduit/shielding, if present). This tests the insulation between the conductor and ground.

Line to Neutral

If you want, you can then connect one lead to the Line conductor and one to the Neutral conductor.

Guard Terminal (If Applicable)

Some meggers have a "guard" terminal. This is used to eliminate surface leakage current from affecting the readings. Consult the megger's manual for proper use of the guard terminal. It's generally used when you suspect surface contamination.3.

Apply Voltage

Select the appropriate test voltage on the megger. For 277V systems, 500V DC is often sufficient. If in doubt, consult the heat trace manufacturer's specifications.

Apply the voltage for a specified period of time (typically 60 seconds). Observe the resistance reading on the megger. Note the reading.4.


Discharge

Very important! After the test, discharge the heat trace cable by shorting the conductors to ground. This will remove any stored charge in the cable's capacitance. Some meggers have an automatic discharge function.5.

Record and Interpret

Record the megger reading, the test voltage, the temperature, and the date/time of the test. Compare the reading to the expected values or previous readings for the same cable.

Troubleshooting Low ReadingsIf you get a low megger reading:1.

Visual Inspection

Carefully inspect the entire length of the heat trace cable for any signs of physical damage (cuts, abrasions, kinks, etc.). Pay close attention to areas where the cable is bent or routed through tight spaces.2.

Check Connections

Inspect all connections in the junction box and along the heat trace run. Look for loose connections, corrosion, or moisture.3.

Sectionalize (if possible)

If the heat trace run is long, try to isolate sections of the cable to narrow down the location of the fault. You can do this by disconnecting the cable at intermediate junction boxes.4.

Dry It Out

If you suspect moisture, try to dry out the cable. You can use a heat gun (carefully, avoiding overheating the cable) or allow it to air dry in a warm, dry environment. Re-test after drying.5.

Replace Suspect Sections

If you find a damaged section of cable, it must be repaired or replaced. Use only approved heat trace splicing kits designed for that specific type of cable.6.

Consult the Manufacturer

If you're still unsure about the megger readings or how to troubleshoot the problem, contact the heat trace manufacturer for assistance.

Important Considerations for Self-Regulating Heat Trace

Parallel Resistance

Self-regulating heat trace has a parallel resistance path due to the semi-conductive core material. This means that even a perfectly good cable
will have a finite resistance to ground. You won't see "infinite" resistance like you might with a standard insulated wire.

Manufacturer's Data

Always consult the heat trace manufacturer's data sheet for the specific cable you are testing. They may provide guidance on acceptable megger readings. Some manufacturers may even recommend against megger testing their self-regulating cables, as high-voltage testing can potentially damage the conductive polymer core.

In SummaryMegger testing heat trace is a critical part of ensuring a safe and reliable installation. Understanding the expected readings, the factors that influence those readings, and how to troubleshoot low readings is essential for properly maintaining heat trace systems. Always prioritize safety and consult the manufacturer's documentation for specific recommendations. Low readings should always be investigated and corrected before energizing the system. Flag for review

Previous Question Next Question