Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: 600a service

User: mannyb, Location: Florida

Asked on: Monday, November 25, 2024 at 8:15 pm EST
Answered on: Thursday, March 6, 2025 at 5:40 am EST

Question: Can I use paralleled 300 mcm copper for 600a service conductors. paralleled 300s is 570amps next higher fuse/breaker 600a.

Okay, let's break down the code requirements and address your specific situation with paralleled 300 MCM copper conductors for a 600A service.

NEC Requirements: Key Considerations1. Ampacity

The combined ampacity of the conductors must be at least equal to the rating of the overcurrent protection device (breaker or fuse) and the load served.2.

Termination Temperature

Pay very close attention to the termination temperature ratings of the equipment (breakers, lugs, panels, etc.). This often limits the allowable ampacity of the conductors. Typically, terminations are rated for 75°C. You

MUST
use the 75°C ampacity column from NEC Table 310.16 unless the equipment is specifically marked and listed for use with 90°C conductors at their 90°C ampacity. Assume 75°C unless proven otherwise.3. Parallel Conductors

NEC 310.10(H) lays out very specific rules for paralleling conductors. Most importantly: They must be the same length, conductor material, insulation type, have the same termination methods, and be in the same raceway or cable. You must have the same number of conductors for each phase, neutral, and equipment grounding conductor.4.

Overcurrent Protection

NEC 240.4 states that you can protect conductors at the next higher standard overcurrent device if ALL of the following conditions are met: The conductors ampacity is less than the rating of the OCPD The conductor is not a tap conductor The overcurrent device is rated 800 amps or less The next higher standard overcurrent device does not exceed 800 amps

Applying the Code to Your Situation
Ampacity of 300 MCM Copper

From NEC Table 310.16, 300 MCM copper has an ampacity of:

285 amps at 75°C
320 amps at 90°C Two paralleled 300 MCM conductors would have a combined ampacity of: 570 amps at 75°C (285 amps x 2) 640 amps at 90°C (320 amps x 2) Your Proposal

You're proposing to use a 600A breaker/fuse.

Analysis



75°C Terminations

If your equipment terminations are only rated for 75°C (which is highly likely), you are limited to the 570 amp total ampacity. Using the "next size up" rule in 240.4 is permitted in this case.

Example Scenario (Most Common): 75°C Terminations


Let's assume your breaker and panel lugs are only rated for 75°C.1. Conductor Ampacity

570 amps.2.

Breaker/Fuse

600 amps.3.

Application of NEC 240.4

You are permitted to use a 600A overcurrent device on the 570 amp rated conductors, because the overcurrent device is rated 800 amps or less and the next higher standard OCPD rating does not exceed 800 amps.

Important Considerations



Load Calculation

Make sure your load calculation
actually requires 600 amps. Don't upsize unnecessarily. If the load is significantly less, you can reduce the conductor size and breaker size, potentially saving money.

Voltage Drop

Check voltage drop. Paralleling conductors helps with voltage drop, but it's still a calculation you should perform.

Grounding

Ensure your grounding conductors are sized correctly. See NEC Table 250.122. With parallel conductors, the grounding conductor is often required to be larger.


Raceway Fill

Ensure you are not exceeding the allowable fill for the conduit or raceway containing the conductors.

In summary

Using parallel 300 MCM copper conductors with a 600A overcurrent device can be code-compliant, if your equipment is rated for 75°C, and all the other requirements are met.
Consult with a Qualified Electrician



Electrical work can be dangerous.
Always consult with a licensed and qualified electrician to ensure your installation meets all applicable codes and safety standards. This response is for informational purposes only and does not constitute professional electrical advice. Flag for review

Previous Question Next Question