User: stang623, Location: Upstate, SC
Asked on: Tuesday, November 26, 2024 at 3:36 pm EST
Answered on: Thursday, March 6, 2025 at 5:42 am EST
Question: Hey guys, have a new tenant we need to take care of in an industrial building. Looking set two panels and pull 4/0 aluminum wire 500 feet and 385 feet and wanting to use aluminum conductor's. Tenant is a know it all and skeptical on aluminum wire. We are planning to pull wire and use the following crimp connectors on the MLO panels, will remove the set screw lug type connectors on the panel and use these instead. YA-A style from burndy.
Okay, let's break down your plan and address the tenant's skepticism regarding aluminum conductors. You're on the right track with using proper termination methods. Here's a detailed analysis
Your Plan (Recap):
Two New Panels
You are installing two new panels to supply the new tenant.
4/0 Aluminum Wire
You plan to use 4/0 aluminum wire as your conductors.
Lengths
One run of 500 feet, another of 385 feet.
Termination
You plan to replace the mechanical (set screw) lugs in the panels with Burndy YA-A series compression lugs.
Addressing the Tenant's Skepticism about Aluminum Conductors
The key to successfully using aluminum conductors in power distribution is proper installation and termination. Past issues with aluminum wiring in residential branch circuits were largely due to:
Improper Alloys
Older alloys were more prone to oxidation and expansion/contraction issues. Modern aluminum alloys are far superior.
Poor Termination Methods
Using non-rated or improperly installed terminations led to loose connections, oxidation, and overheating.
Lack of Anti-Oxidant Compound
Oxidation between the aluminum conductor and the termination material increases resistance and heat.Here's how you can address the tenant's concerns and demonstrate your professionalism:1.
Education
Explain that aluminum wiring is a standard and safe practice in commercial and industrial power distribution. The primary difference between using aluminum and copper is the larger ampacity required for the conductors. Tell him we will be pulling much larger aluminum conductor vs what size conductor he would need to pull in copper and the voltage drop will be less in aluminum because we are pulling a larger sized conductor.2.
Modern Alloys
Explain that modern aluminum alloys (e.g., AA-8000 series) are specifically designed for electrical applications and are significantly more stable and less prone to corrosion and expansion/contraction issues than older alloys.3.
Proper Termination is Key
Emphasize that the correct installation of the conductor is important and will be performed using proper techniques, and materials designed to use aluminum conductor such as the ya-a burndy crimp connectors.4.
Code Compliance
Assure him that all work will be performed in compliance with the National Electrical Code (NEC) and local codes.5.
Experience
Let the tenant know that you have experience working with aluminum conductors and are confident in your ability to provide a safe and reliable installation.
Analysis and Recommendations
4/0 Aluminum Ampacity
4/0 Aluminum has an ampacity of 180 amps at 75 degrees c.
Voltage Drop
4/0 Aluminum over 500 feet and 385 feet is a concern. Calculate the voltage drop based on the tenant's expected load. It is critical to get this information from the tenant.
Termination
Burndy YA-A Lugs
You are on the right track using Burndy YA-A series compression lugs. These are high-quality lugs specifically designed for aluminum conductors. Make sure you select the correct size YA-A lug for the 4/0 conductor and the panel's busbar/connector size.
Crimping Tool
Absolutely critical
Use the correct crimping tool and die specified by Burndy for the YA-A lugs and 4/0 aluminum conductor. Using the wrong tool will result in a faulty connection and potential problems. Document the crimping process (photo or log) to show proper installation.
Anti-Oxidant Compound
Essential
Apply a listed anti-oxidant compound (e.g., Penetrox A) to the aluminum conductor before inserting it into the lug. This compound prevents oxidation and ensures a good electrical connection.
Torque
If your panel requires torque of connections, be sure to torque the connection to spec.
Conduit Fill
Ensure the conduit fill percentage is within NEC limits for the conduit size you are using.
Neutral/Ground
Consider the need for a neutral conductor and an equipment grounding conductor. Size these appropriately according to the NEC.
Grounding
Ensure proper grounding of the panels and equipment.
Steps to Take Before Starting the Project
Load Calculation
Get a detailed load calculation from the tenant. This is essential for proper conductor sizing and voltage drop calculations. Have them specify the maximum expected load (in amps or kVA) and the power factor.2.
Voltage Drop Calculation
Perform a thorough voltage drop calculation for both the 500-foot and 385-foot runs. Use the maximum expected load to determine if 4/0 aluminum is sufficient, or if you need to upsize the conductors to minimize voltage drop. Voltage drop should be less than 3% at the panel.3.
Panel Selection
Confirm that the panel you've selected is appropriately sized for the tenant's load and has the correct voltage and phase configuration.4.
Permitting
Obtain all necessary permits before starting any work.
Important Considerations Regarding Aluminum vs. Copper
Cost
Aluminum is generally less expensive than copper, especially for larger conductor sizes.
Weight
Aluminum is lighter than copper, which can make it easier to handle and install, particularly for long runs.
Expansion and Contraction
Aluminum expands and contracts more than copper with temperature changes. This is why proper termination and anti-oxidant compound are crucial.
Corrosion
Aluminum is more susceptible to corrosion than copper, especially in the presence of moisture and dissimilar metals. Anti-oxidant compound mitigates this.
Example of how to talk to the tenant
"We understand your concerns about using aluminum conductors, and we want to assure you that we're taking all necessary precautions to ensure a safe and reliable electrical system for your business. Modern aluminum alloys are significantly improved, and the key is proper installation. We'll be using Burndy YA-A compression lugs, which are specifically designed for aluminum conductors, along with anti-oxidant compound to prevent corrosion. We'll be using the correct crimping tool and die, and we'll torque all connections to the manufacturer's specifications. We will also provide all load calculations and voltage drop calculations to ensure we are providing the correct and safe installation for you."
Disclaimer: I am an AI chatbot and cannot provide electrical engineering advice. This information is for general guidance only. Always consult with a licensed and qualified electrical contractor or engineer for your specific project and to ensure compliance with all applicable codes and regulations.* Flag for review