User: Capt sexy, Location: Charleston
Asked on: Wednesday, November 27, 2024 at 11:58 am EST
Answered on: Thursday, March 6, 2025 at 5:44 am EST
Question: Generator turns on when power is lost but doesn’t transfer power to house. Also shuts down correctly when power is restored?
This sounds like a frustrating situation. Here's a breakdown of the likely culprits and how to troubleshoot them, focusing on the common issues and safety
Understanding the System
Automatic Transfer Switch (ATS)
This is the key component that switches your house from grid power to generator power. It's what's supposed to be sending power to your home.
Generator
Your power source during an outage.
Utility Grid
Your normal power source.
Possible Causes and Troubleshooting (Start with the simplest and SAFEST first!)1. Safety First: Before Doing Anything TURN OFF THE GENERATOR
Seriously. Turn it off and let it cool down.
TURN OFF THE MAIN BREAKER to your house
This disconnects you from the grid and adds another layer of safety.
READ YOUR GENERATOR AND ATS MANUALS
These will have specific troubleshooting steps for your model.
If you are not comfortable working with electricity, call a qualified electrician. Electricity is dangerous!2. Basic Checks (After Safety Measures)
Generator Output
Is the generator actually producing power? Many generators have a voltmeter or indicator light. Check this. Check the generator's breakers
Most generators have a breaker or two on the output side. Make sure these are on.
Check the generator for error codes
Some have diagnostic features.
Fuel
Is there enough fuel in the generator? Low fuel can cause shutdowns, even if it starts.
Oil
Check the oil level. Many generators have low-oil shutoff switches.
3. Automatic Transfer Switch (ATS) Issues
ATS Power
Does the ATS have power? It needs power to operate. Often it is powered by a breaker on the generator. Check this breaker. ATS Error Codes or Indicators
Many ATS units have lights or a display that indicates their status. Check for any error codes. Consult the ATS manual.
ATS Stuck/Malfunctioning
This is a common problem. The ATS has mechanical contacts that physically switch the power source. Sometimes these contacts get stuck or corroded.
Listen closely
When the power goes out and the generator starts, can you hear the ATS trying to switch? You should hear a distinct "clunk" or click as it throws the switch. If you don't hear anything, the ATS is likely not even attempting to switch.
Visual Inspection (with the generator and main breaker OFF)
If you're comfortable and know how to safely work around electricity, open the ATS panel (following safety precautions). Look for: Burned wires or connections. Corrosion on contacts. Loose wiring. Anything that looks out of place.
4. Wiring Issues Loose Connections
Vibration from the generator can loosen connections over time. Check all wiring connections at the generator, the ATS, and your main breaker panel.
Damaged Wiring
Look for frayed, cracked, or chewed wires (rodents love to nest in these things).
Incorrect Wiring
If the generator or ATS was recently installed or modified, double-check the wiring diagrams to make sure everything is connected correctly.
This is a job best left to a qualified electrician.5. ATS Settings/Programming
Time Delays
Some ATS units have programmable time delays. It's possible a delay is set too long, or is set incorrectly. Check the ATS manual.
Voltage Sensing
The ATS monitors the grid voltage. If it's not sensing the loss of power correctly, it won't switch. This could be a faulty voltage sensor.
Troubleshooting Steps (in order)
Safety First
Turn everything off (generator and main breaker).2.
Basic Checks
Fuel, oil, generator breakers, generator output (voltmeter reading).3.
Listen to the ATS
Does it attempt to switch when the generator starts?4.
ATS Power
Is the ATS powered? Check the breaker that feeds it.5.
Visual Inspection of ATS (with power OFF)
Look for obvious damage, loose connections, or corrosion.6.
Check wiring
Look for loose, damaged, or improperly connected wires.7.
Consult Manuals
Refer to the generator and ATS manuals for specific troubleshooting steps and error codes.8.
Call a Professional
If you've exhausted these steps and are still having problems, it's time to call a qualified electrician or generator technician.
Important Notes
Generator Size
Is your generator sized correctly for your house? If it's too small, it might not be able to handle the load, and the ATS might not switch over. However, if it starts and runs, this is less likely the problem.*
Code Compliance: Make sure your generator and ATS installation comply with local electrical codes.Good luck! Take your time, be careful, and don't hesitate to call a professional if you're not comfortable. Flag for review