Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: 100 AMP Panel Load!

User: Prototype1, Location: Kansas City

Asked on: Wednesday, November 27, 2024 at 12:00 pm EST
Answered on: Thursday, March 6, 2025 at 5:44 am EST

Question: Okay, I am going to sound dumb. But I want to understand the stuff.I have a 300-amp main panel and a 100-amp sub-panel, which is fed from the main panel. The sub-panel is protected by its own 100-amp breaker located in the main panel.The 100-amp sub-panel is dedicated to powering park trail lights, pickleball court lights, and tennis court lights.### Sub-Panel Details:The 100-amp sub-panel has 30 breaker slots. The current configuration of branch devices is as follows:#### Branch Devices:| Quantity | Poles | Trip Rating | Voltage ||----------|-------|-------------|---------|| 5 | 2 | 20 A | 208 V (single phase) || 3 | 1 | 20 A | 120 V (single phase) || 17 | 1 | Spare | — |#### Main Breaker Device:| Quantity | Poles | Trip Rating ||----------|-------|-------------|| 1 | 3 | 100 A |---I understand that the total current draw from all breakers in the main service panel should not exceed 80% of its capacity, per NEC guidelines. For example, a 20-amp breaker can support up to 16 amps of continuous load (80% of its rated capacity).Question:Given this understanding, I am confused about how many 20-amp breakers I can install in the sub-panel. Specifically:1. The sub-panel already has five 20-amp, 208V single phase breakers and three 20-amp, 120V breakers.2. When I total the amperage ratings, they appear to exceed the sub-panel's 100-amp capacity.Could you clarify how this works? Does this mean the breakers’ combined ratings (e.g., 5 x 20 amps + 3 x 20 amps) exceed 100 amps, or is this more about the actual current draw on each breaker?I have to add dedicated circuits for the grill, oven and receptacle (GFCI) as it is outside in park. So, I am calculate how many slots will be left in a 100 amp panel that has 30 slots.

Okay, let's break this down and clear up the confusion. You're right to be thinking critically about the sub-panel capacity! The key concept here is diversity and load calculation.

Understanding Diversity and Load Calculation

The reason you can have more than 100 amps worth of breakers in a 100-amp panel is because not everything is going to draw its maximum rated current at the same time. This is the principle of diversity. Load calculations are about estimating the maximum likely current the panel will experience.

Why the Sum of Breaker Ratings Doesn't Equal Total Load

Imagine your home's main panel. It likely has far more than its rated amperage worth of breakers. If you turned everything on at once (every light, appliance, hair dryer, etc.), you'd probably trip the main breaker. But in normal use, that rarely happens. Electrical codes allow for this by using specific formulas and derating factors to estimate the actual load.

Applying this to Your Sub-Panel

Here's how to approach your sub-panel situation:1. Existing Load

You need to determine the actual continuous load on those existing breakers, not just the breaker rating. Breaker ratings are the maximum allowed current, not the guaranteed current draw. The actual continuous load is what the lights connected to those breakers draw when they are all turned on and running continuously for 3 hours or more. You'll need to know the wattage of the fixtures connected to each breaker to calculate this load. The formula is: Amps = Watts / VoltsFor the 208V circuits, it's: Amps = (Total Watts of fixtures on the circuit) / 208For the 120V circuits, it's: Amps = (Total Watts of fixtures on the circuit) / 120Don't forget the 80% rule. So, if a 20A breaker is running 16A continuously, that's ok.2.

New Load (Grill, Oven, Receptacle)

This is where you need to do a proper load calculation.


Grill

Find the wattage of the electric grill. Calculate the amperage. Assume it's a continuous load. If it is gas grill, will there be an igniter that require power?

Oven

Find the wattage of the electric oven. Calculate the amperage. Assume it's a continuous load.


Receptacle (GFCI)

You can't just guess at the load here. What is the purpose of the outlet? What do you anticipate using it for? For a general-purpose receptacle, a good rule of thumb for load calculations is to assume at least 180 VA (Volt-Amps, which is essentially watts for calculation purposes) per outlet, and more if you anticipate specific high-draw equipment (like a pressure washer, which is unlikely for a park but is an example).3.

Load Calculation


This part is crucial. You need to calculate the total estimated maximum continuous load on the sub-panel. This isn't just adding up the breaker ratings! There are specific code rules and tables you must consult for calculating loads. NEC Article 220 outlines the specific requirements for load calculations. It's best to err on the side of caution and assume a generous load for the receptacle unless you have a very specific use case.You need to calculate the total demand load and verify that the load of all branch circuits is <= 80 amps.4. Compare Total Load to Sub-Panel Capacity

After doing a proper load calculation, compare the total demand load to the 100-amp capacity of your sub-panel. If the total demand load exceeds 80 amps, you can not add any branch circuits or increase the capacity of existing circuits.

Important Considerations



208V vs. 120V

The voltage is crucial for calculating the
actual amperage draw of an appliance. A 1000-watt appliance will draw less current at 208V than it will at 120V.

Continuous Loads

Any load expected to operate for 3 hours or more is considered a continuous load and must be factored in at 125% of its full load value (the 80% derating rule).

Safety

Electrical work can be dangerous and must be done by a qualified and licensed electrician.

What About the Slots?


You have 30 slots.
5 x 2-pole breakers = 10 slots used 3 x 1-pole breakers = 3 slots usedTotal slots used = 13Total slots available: 30-13 = 17.If you need a 2 pole breaker for the oven, you have 17 available slots. If you can use only 1-pole breakers for the grill, oven, and receptacle, you can install 14 branch circuits. If you need two, 2-pole breakers and one, 1-pole breakers, you can install 11 branch circuits.

In Summary

Don't just add up breaker ratings. Perform a proper load calculation
using the NEC guidelines to determine the total demand load on your sub-panel. This will tell you if you have enough capacity to add those new circuits for the grill, oven, and receptacle. I highly recommend* consulting with a qualified electrician to perform this calculation and ensure the safety of your installation. Flag for review

Previous Question Next Question