Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: POCO has nuisance transformer fuse melts

User: 11bgrunt, Location: TEXAS

Asked on: Monday, December 2, 2024 at 11:42 pm EST
Answered on: Thursday, March 6, 2025 at 5:50 am EST

Question: Large car wash will experience random outages caused by a POCO overhead transformer fuse melting. This happens a few times a year.I am adding a voltage recorder on the secondary this week.The service is 400A, 480Y/277. POCO has three 100kVA transformers fused 15T on 24.9Y/14.4kV.The general rule is this fuse melts at X2 the rating after five minutes. This time only one transformer fuse melted but have seen all three melted at the same time.That math is 432kVA at least.The attendant said the large drying fans were running, turned off and when they restarted, the fans were still turning. That is when the POCO fuse melted.A thought I had was the turning motor acts a generator and when the contactor closes to start that motor again, the voltages are not in synch.The first thought was a turning motor would reduce inrush because it was already turning.The attendant said they have a similar random issue at another one of their locations.Possible?A motor restart time delay has worked on turbine water well sites that melted POCO transformer fuses.Thanks,

You're on the right track. Here's a breakdown of the likely causes and solutions

Understanding the Problem
Motor Restart Inrush (The Primary Suspect)

You're correct. When a motor is spinning down, and you re-energize it, it can act like a generator and cause a massive inrush current. This is far greater than a standard across-the-line start. The spinning motor is producing a voltage, and the grid is producing a voltage. If they are out of phase when you slam the contactor shut, the motor essentially becomes a short circuit for a brief period as the voltages try to equalize.


Overloading

Even without the spinning fan issue, you need to consider the total load. A 400A, 480V service could be overloaded, especially if the car wash has numerous pumps, heaters, and other equipment running simultaneously. Even if the load seems within limits under normal conditions, it is likely to not be under the restart conditions described.

Transformer Capacity

The POCO's transformers are sized appropriately for the service. Three 100kVA transformers deliver 300kVA. Even derating for 80% continuous load, that leaves 240kVA. 400A at 480V yields 332kVA. A large car wash probably has other equipment running on 120V and 208V.

Why the Spinning Fans Matter
Phase Angle

As you mentioned, the key is the phase angle between the motor's back-EMF and the supply voltage when the contactor closes. If these are significantly out of phase, the current surge is dramatic.

Increased Current

The inrush is not just overcoming inertia; it's forcing a voltage and current that are not synchronized.

Troubleshooting Steps
1. Voltage Recorder Data



Voltage Sags

Capture the voltage dips that occur during startup and especially during the suspected restart events. How low does the voltage drop? Does it drop on all phases or just one?

Harmonics

Check for harmonic distortion. High harmonics can contribute to transformer heating and premature fuse failure.


Transients

Look for voltage spikes or transients. These could be caused by other equipment switching on/off or by lightning strikes.2.

Current Measurements



Inrush Current

Use a clamp meter with inrush current capability on the motor feeders. Capture the peak inrush current during both a normal start and a start with the fan already spinning. Compare these values.


Total Load Current

Monitor the overall load current on the 400A service.

Transformer Loading

Measure the current on each of the POCO's transformer legs. This will show if one transformer is disproportionately loaded.3.

Motor Data



Nameplate Information

Confirm the HP, voltage, FLA, and service factor for each of the fan motors.

Motor Condition

Check the motor windings for insulation breakdown. Perform a megger test.


Motor Starters

Inspect the contactors and overload relays. Ensure they are in good condition and sized correctly.4.

POCO Coordination



Fuse Coordination Study

The POCO should have a fuse coordination study. Request to see it. This will show the time-current curves for their fuses and the equipment's protection devices.


Transformer Impedance

Ask the POCO for the transformer impedance (%Z). This is needed for calculating fault currents.

Solutions
1. Restart Time Delay (Your Best Bet)



Implementation

Install a time delay relay on the motor starters for the fans. Set it to a few seconds (start with 3-5 seconds) to allow the fans to coast to a stop before the motor is re-energized. This is the simplest and often most effective solution.


Adjustability

Make the time delay adjustable so you can fine-tune it.2.

Soft Starters



Motor Control

Replace the across-the-line starters for the fan motors with soft starters. Soft starters gradually ramp up the voltage to the motor, reducing inrush current. This is a more expensive solution than a time delay relay but will reduce stress on the electrical system.3.

Variable Frequency Drives (VFDs)



Precise Control

A VFD offers the most sophisticated control. It can vary the motor speed and reduce inrush current to almost nothing. This is the most expensive option.4.

Staggered Starting



Load Distribution

If possible, design the system so that the fans start at slightly different times. This will spread out the inrush current.5.

Power Factor Correction



Improved Efficiency

Install power factor correction capacitors. This will improve the power factor of the car wash, reducing the overall current draw and the stress on the transformers.6.

Increase Transformer Capacity (Least Likely and Most Expensive)



If Overload is the Issue

Only if your load measurements show that you are consistently overloading the transformers would you need to consider upgrading them. This is a last resort.

Important Considerations
Safety

Always work with qualified electricians when dealing with electrical equipment.

Coordination

Coordinate any changes with the POCO.


Documentation

Document all troubleshooting steps, measurements, and solutions.

In Summary


The restart time delay is the most likely solution, but you need to gather data to confirm the root cause and ensure that other factors (overloading, harmonics) are not contributing to the problem. Install a time delay and start with a few seconds. Then run the equipment for several days and see if it solves the problem. Flag for review

Previous Question Next Question