Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Setback for plumbing and exhaust vents on noncommercial

User: SunnyD, Location: California

Asked on: Tuesday, December 3, 2024 at 12:26 pm EST
Answered on: Thursday, March 6, 2025 at 5:51 am EST

Question: I am working on a design where the contractor added plumbing and exhaust vents in the middle of the array area and want to know how far a PV module must be from one of those vents. Assume this is in the middle of the roof and the project already has fire path access satisfied on the edges and every 150' of array.Is there a code that prescribes what the minimum setback should be from a plumbing or exhaust vent to a solar module?

You're right to be concerned about the proximity of plumbing and exhaust vents to PV modules. While there isn't a single, universally applicable code that dictates the exact setback distance for all scenarios, here's a breakdown of the relevant considerations and where to look for guidance

Key Considerations:

1. Manufacturer's Instructions

This is the most important first step. PV module manufacturers often specify minimum clearances from obstructions, including vents and chimneys, in their installation manuals. These instructions are paramount and override general guidelines. Reasons for these clearances include:

Shading

Even partial shading significantly reduces a PV module's output.


Overheating

Restricting airflow around modules can lead to excessive heat buildup, reducing efficiency and lifespan.

Accessibility

Leaving enough space allows for future maintenance and repairs.


Wind Loading

Obstructions nearby the array will change wind loads and could impart an increased wind load on the array.

Plumbing maintenance

Sufficient clearance must be maintained for easy and safe access to perform plumbing maintenance.2.

Building Codes (IBC/IRC)



Mechanical Code (IMC/UMC)

Refer to the International Mechanical Code (IMC) or Uniform Mechanical Code (UMC), if adopted by your jurisdiction. These codes address exhaust vent termination locations to prevent re-entrainment of exhaust gases into the building. While they don't specifically address PV modules, they may provide guidance on vent clearances that could indirectly affect PV module placement. For example, they specify distances from operable windows, doors, and air intakes. The intent is to prevent contaminants from entering the building and the same principle is applicable to the modules where chemicals could cause corrosion or shading from grease/debris.

Fire Codes (IFC)

The International Fire Code (IFC), may have requirements related to roof access and spacing that indirectly affect PV module placement. While you've addressed fire access on edges and at 150' intervals, local interpretations can vary.3.

National Electrical Code (NEC)

The NEC doesn't explicitly dictate vent setbacks. However, Article 690 (Solar Photovoltaic (PV) Systems) addresses issues related to safe installation and operation, including conductor sizing, overcurrent protection, and grounding. Improper placement of modules near vents could indirectly impact these aspects.4.

Local Jurisdictional Requirements



Local Amendments

Many jurisdictions amend the national codes. Check with your local building department for any specific requirements or interpretations regarding PV module installations and vent clearances.


Permitting Authority

The permitting authority has the final say. Consult with them early in the design process to ensure compliance and avoid costly revisions later.5.

Best Practices/Industry Standards

*

NABCEP (North American Board of Certified Energy Practitioners)

NABCEP-certified installers often follow best practices that exceed minimum code requirements. These practices often include larger clearances around obstructions for ease of maintenance and improved performance.

Recommended Actions


Consult Module Manufacturer's Instructions

This is paramount. Find the installation manual for the specific PV module being used and adhere to their recommendations.2.

Contact Local Building Department

The most reliable way to determine the required setback is to contact the local building department or permitting authority. They can provide guidance based on local codes and interpretations. Provide them with the model number of the PV modules, the type and height of the vent.3.

Consult with a Licensed Engineer/Designer

An engineer specializing in PV systems can perform a site-specific analysis, considering all relevant factors, and determine the optimal placement of PV modules to minimize shading, ensure proper ventilation, and comply with all applicable codes.4.

Document Everything

Keep detailed records of all communications with manufacturers, building departments, and engineers. This documentation will be crucial during the permitting process and any future inspections.

Example Scenario

Let's say the PV module manufacturer specifies a minimum clearance of 12 inches from any obstruction. You also have a 4" diameter plumbing vent that extends 24 inches above the roof. In this case, you would need to ensure that the closest edge of the PV module is at least 12 inches away from the outer edge of the vent. You may also want to consider a larger setback to account for potential shading from the vent at different times of the year.

In summary, there's no single "magic number" for the setback distance. It depends on a combination of manufacturer's instructions, local codes, and best practices. Prioritize the manufacturer's recommendations, consult with your local building department, and consider engaging a qualified professional to ensure a safe and code-compliant installation.
Flag for review

Previous Question Next Question