Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: 250.21 (2017NEC)

User: Isaiah, Location: Baton Rouge

Asked on: Wednesday, August 6, 2025 at 1:03 pm EDT
Answered on: Wednesday, August 6, 2025 at 1:03 pm EDT

Question: If I have a 3phase, 3wire, delta-delta XFMR 13.8kV-480V, UNGROUNDED do I still need to provide a fault path back to the transformer, along with ground detectors as described in 250.21?Enviado desde mi iPhone utilizando Tapatalk

Yes, you absolutely need to provide a fault path back to the transformer, and you should strongly consider ground detection for an ungrounded delta system. While the Code doesn't mandate providing an intentional ground on an ungrounded system, it does mandate having a fault path capable of carrying fault current back to the source. This applies regardless of whether the system is grounded or ungrounded.Here's a breakdown

Why You Need a Fault Path (Equipment Grounding Conductor - EGC):
Safety

The primary purpose of an Equipment Grounding Conductor (EGC) is safety. In the event of a ground fault (where a phase conductor accidentally comes into contact with a metal enclosure or equipment frame), the EGC provides a low-impedance path for fault current to flow back to the transformer. This high current flow is essential to quickly trip overcurrent protection devices (circuit breakers or fuses) and de-energize the faulted equipment. Without this low-impedance path, the fault current could be too low to trip the breaker, resulting in the metal enclosure remaining energized at a potentially dangerous voltage.


NEC Requirements

Article 250 of the NEC provides the requirements for grounding and bonding, but the following sections apply to ungrounded systems and the requirement for a fault path:

250.4(A)(3): Ungrounded AC Systems

This section explicitly states the requirement for Equipment Grounding Conductors (EGCs) in ungrounded systems. It doesn't excuse you from having them simply because the system isn't grounded. It states that these systems
shall comply with 250.4(A)(4) and (5) which detail providing the EGC.

250.96(A): Bonding Other Enclosures

Requires bonding of metal raceways, cable trays, and other metal enclosures to ensure electrical continuity and a reliable fault current path.

250.118: Types of Equipment Grounding Conductors

Specifies acceptable types of EGCs (e.g., wire, rigid metal conduit, etc.).

Why Ground Detection is Highly Recommended (Though Not Always Mandated)



Early Fault Detection

An ungrounded system can continue to operate with a single ground fault. This is often considered an advantage because production isn't immediately interrupted. However, this situation is dangerous! The first ground fault energizes the entire system with respect to ground. A second ground fault on a different phase will create a phase-to-phase short circuit through the equipment, resulting in a potentially catastrophic fault and a much higher likelihood of equipment damage and personnel injury.

Preventing Transient Overvoltages

Ungrounded systems are susceptible to transient overvoltages during switching or arcing ground faults. These overvoltages can damage equipment insulation and lead to premature failures.


NEC Recommendations

While NEC 250.21 covers ungrounded systems, it leans heavily on recommending Ground Detection:

250.21(B): Ground Detectors.
"Ungrounded ac systems as permitted in 250.21(A) shall be equipped with ground detectors that provide an indication of the presence of a ground fault on the system." While not always required, this section strongly suggests the use of ground detectors. The exception only applies when a system interruption can be tolerated and will clear the fault. Code Enforcement

Many inspectors expect to see ground fault detection on ungrounded systems, even if not explicitly required in every situation. It demonstrates a commitment to safety.

Ground Detection Methods

Common methods for ground detection on ungrounded delta systems include:

Ground Lamps (or Pilot Lights)

Three lamps connected from each phase to ground. Equal brightness indicates no ground fault. A dim or extinguished lamp indicates a ground fault on that phase. Simple, but not very precise.


Ground Detectors with Meters

More sophisticated devices that measure the voltage or current to ground and provide a more accurate indication of the fault.

Ground Fault Indication Relays

Relays that trip an alarm or disconnect the system upon detecting a ground fault.

In Summary



Provide a low-impedance fault path (EGC) for all equipment, regardless of whether the system is grounded or ungrounded. This is REQUIRED by the NEC.
* Install ground detection to provide early warning of a ground fault and prevent potentially catastrophic failures. This is HIGHLY RECOMMENDED and expected in many cases.

Consult with a qualified electrical engineer to determine the best grounding and ground detection strategy for your specific application, considering the size and complexity of the system, the potential for downtime, and safety requirements. Flag for review

Previous Question Next Question