Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Breakers tripping when power goes out.

User: bcl, Location: Garden Ridge, TX

Asked on: Wednesday, August 6, 2025 at 3:05 pm EDT
Answered on: Wednesday, August 6, 2025 at 3:08 pm EDT

Question: Hey all, I've got a customer who says his power goes out often where there are a lot of new homes being built. Whenever the power goes out, multiple single pole breakers trip. I think it's the AFCI breakers, but he can't really confirm. Set up is main breaker/ service panel exterior, lighting and outlets on the interior sub panel. The interior breakers are the ones tripping. He said once that all the breakers on one side of the panel had tripped when the power came back on, other times it's just a few breakers. He's not the only one in the neighborhood who is having the same problem.The only work I've done on the house is install a surge protector (Siemens FSPD), it was built in 2016.I've swapped out a number of spec grade CH AFCI breakers in the same neighborhood that begin nuisance tripping after 3-4 years, but I haven't had a problem with them tripping every time the power goes out and comes on again.Any suggestions? POCO doesn't take any responsibility, and the problem isn't going away as long as there is new construction going on in the neighborhood. The power goes out a couple times a month.

Okay, this is a frustrating problem, but let's break it down and explore some possible causes and solutions. The fact that multiple houses are experiencing the same issue points to a utility grid problem, but we still need to ensure the customer's electrical system is behaving as it should.Here's a structured approach

1. Confirm the Breakers are Definitely AFCI:
Ask the Customer (Again)

Stress the importance of knowing. AFCI breakers have a "test" button. Have them visually inspect a tripped breaker after a power outage and confirm it's an AFCI. If it
is an AFCI, it'll have a pigtail neutral connection.

Visual Inspection (by You)

If possible, you need to see the panel and confirm the breaker type.

2. Document Specifics After an Outage



Which Breakers Trip?
The next time it happens, get a precise list of exactly which breakers trip. Are they on the same phase (bus bar)? Are they all related to the same branch circuit? This is critical for understanding the pattern. This is best handled by instructing the customer on what information you need from them. Sequence of Events

Does anything specific happen before the power goes out (e.g., lights flicker, appliances hum)? How quickly do the breakers trip after power returns? Immediately? After a few seconds?

Time of Day

Are the outages happening at peak load times (early evening)?

3. Analyze the Potential Causes

Here are some possibilities, roughly in order of likelihood:


Voltage Sags/Swells

The new construction is very likely overloading the local grid. This can cause voltage sags before the outage and significant voltage swells after power is restored. AFCI breakers are sensitive to voltage fluctuations, and a spike could easily cause them to trip. The surge protector should help but may be overwhelmed or not reacting fast enough.

Utility Grid Switching/Reclosing

When the grid experiences a fault, the utility will often
quickly try to reclose the circuit (i.e., turn the power back on). If the fault is still present, the breaker trips again. These rapid on-off cycles are brutal on electrical equipment and can definitely trip AFCI breakers. The customer's system may be seeing several rapid power fluctuations before the power stays on.

Neutral Issues (Most Likely)

This is where I'd focus my attention. A shared neutral situation on the utility side, or even inside the house, can cause problems with AFCI breakers. When power is restored, unbalanced loads on a shared neutral can create voltage on the neutral, which AFCIs interpret as a fault. This is especially likely with new construction throwing the grid out of balance.

Neutral-Ground Bonding

Verify correct neutral-ground bonding in both the main panel and the subpanel.
There should only be ONE point of neutral-ground bonding, and that is in the service panel/main disconnect. If there is a ground fault, the breaker will trip when power is reestablished.

Harmonics

New construction often involves a lot of electronic equipment (LED lighting, VFDs, etc.) that generates harmonic currents. These harmonics can pollute the neutral and cause AFCI issues.

Faulty Appliances

A faulty appliance on a circuit protected by an AFCI breaker could be triggered by the power surge. The inrush current when the appliance tries to start up after the outage could mimic an arc fault.


Faulty AFCI Breakers (Less Likely, But Still Possible)

It's possible a batch of breakers is defective. While you've already replaced some, it's worth considering.

4. Diagnostic Steps



Voltage Monitoring

The
best way to diagnose this is with a power quality analyzer that can record voltage sags, swells, and transients. This will give you definitive proof of what the grid is doing during an outage. You could rent one of these from an electrical supply house or hire an electrician specializing in power quality analysis.

Neutral-to-Ground Voltage Testing

Measure the voltage between neutral and ground at various outlets, especially on the circuits that are tripping. Ideally, this should be close to zero. A significant voltage reading (over 1-2 volts) indicates a potential neutral issue. This is especially important to check during a period of peak load.

Appliance Testing

If you suspect a specific appliance, unplug it before the next predicted outage (if possible). If the breakers don't trip, that appliance is suspect.


Dedicated Circuit for Sensitive Equipment

Consider suggesting the customer move particularly sensitive electronics (computers, etc.) to a dedicated circuit with its own AFCI breaker and a high-quality surge protector.

Temporary Non-AFCI Breakers (Use with Extreme Caution!)

This is risky and should only be done by a qualified electrician with extreme caution and full understanding of the potential consequences. If you suspect the AFCI breakers are simply too sensitive, you could temporarily replace one or two with standard breakers (same amperage, of course) to see if the problem persists during an outage.

WARNING

This removes arc fault protection. You are taking on significant liability if you do this and there is a fire! This is
strictly for diagnostic purposes. Immediately replace with AFCI breakers once the test is complete. Label the temporary breaker so no one forgets that it is not an AFCI.

Check the Load on the Circuits
If the load is near the breaker limit, and then power returns, all the motors/compressors start up together and trip the breaker.5. Solutions



Talk to the Utility

Even though they're not taking responsibility,
someone needs to complain to them. The more people who complain, the more likely they are to investigate. Document everything meticulously and provide them with dates, times, and specific problems.

Power Conditioner/UPS

For sensitive equipment, a UPS (Uninterruptible Power Supply) or a high-quality power conditioner can provide clean, stable power, even during fluctuations. This is an expensive solution, but it may be necessary.

Whole-House Surge Protector (Already Installed, but Re-evaluate)

Ensure the Siemens FSPD is properly installed and functioning. Check its surge capacity and clamping voltage. It might be worthwhile to upgrade to a higher-capacity unit or add point-of-use surge protectors for particularly sensitive equipment.


Better AFCI Breakers

Consider upgrading to higher-quality AFCI breakers that are known to be less prone to nuisance tripping. Some brands are more sensitive than others. You mentioned having experience with some CH breakers. Research alternatives and consult with other electricians.

Demand Response/Load Shedding

Some utilities offer programs where they can remotely reduce the load on the grid during peak times. This can help stabilize the voltage.


Call the Electrical Inspector

If the utility is unresponsive and the problems are widespread, consider contacting your local electrical inspector. They may be able to pressure the utility to address the issues.

Important Considerations



Safety First

Always prioritize safety. Work on electrical systems only if you are qualified and experienced.


Documentation

Document everything – complaints, test results, actions taken.*

Professional Liability:
Be very careful about offering solutions that could compromise safety. If you're not comfortable with the level of risk, refer the customer to a specialist.This is a complex issue, and there's no easy answer. A systematic approach, careful observation, and potentially some specialized testing are required to get to the bottom of it. Good luck! Flag for review

Previous Question Next Question