Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Hilti TE 22

User: BOBVOLK, Location: SD

Asked on: Wednesday, August 6, 2025 at 3:21 pm EDT
Answered on: Wednesday, August 6, 2025 at 3:40 pm EDT

Question: Has anybody attached a 2 inch coring bit to this drill? What parts do I need to attach a coring bit to this drill? I got it as a gift and no instructionsThanks

Okay, let's figure out what you need to use a 2-inch coring bit with your new drill.

First, Some Cautions and Considerations Drill Type is Crucial

The type of drill you have is
critical to safely and effectively using a coring bit. Coring bits require significant torque and often lower speeds. Trying to use a standard drill for coring can be dangerous and damage the drill. Please let me know the Model number if you do not know the type of drill you have.

Material Being Cored

What material are you trying to core? Concrete, brick, tile, wood, etc., all require different coring bits and techniques. Concrete coring, in particular, usually requires a specialized wet-coring drill.

Safety First

Coring can be dangerous. Always wear appropriate safety gear: safety glasses, gloves, hearing protection, and a dust mask (especially when coring masonry).

General Steps and Possible Parts (Depending on Drill and Material)


Assuming you have a drill that is rated for coring, here are the general things you might need:1. Check the Drill's Chuck



Chuck Size

The coring bit shank must fit into the drill's chuck. Common chuck sizes are 1/2 inch, and 5/8inch. Measure the shank of the coring bit you intend to use. If the shank is too large for your drill's chuck, you cannot use that bit with that drill without adapting.2.

Arbor/Adapter (Likely Needed)

Most coring bits don't have a simple shank that fits directly into a drill chuck. They require an arbor. An arbor is an adapter that has a threaded connection for the coring bit on one end and a shank that fits into the drill's chuck on the other end.

Thread Size

Coring bits have standardized thread sizes (e.g., 1 1/4"-7 UNC, 5/8"-11). You need an arbor with the correct thread size to match your coring bit.

Pilot Drill

Some arbors come with a replaceable pilot drill bit. This helps center the coring bit and gets the hole started.
Example: If you have a coring bit with a 5/8"-11 thread and a drill with a 1/2" chuck, you'd need an arbor that adapts from 5/8"-11 female thread to a 1/2" shank.3.

Extension (Possibly Needed)

If you need to drill a deep hole, you might need a coring bit extension to add length. These usually screw between the arbor and the coring bit.4.

Water Swivel/Dust Collection (For Masonry/Concrete)



Wet Coring

When coring concrete or other hard masonry, using water is highly recommended (and sometimes required) to cool the bit, reduce dust, and improve cutting performance. You'll need a water swivel attachment that connects to the drill and provides a water feed to the coring bit.

Dry Coring (with Dust Collection)

If you're dry coring masonry, use a dust collection shroud that connects to a vacuum to minimize dust exposure.5.

Clutch Setting/Speed Control (On the Drill)



Clutch

A drill with an adjustable clutch is very helpful. Set it to a lower setting so the drill will slip if the coring bit binds up. This prevents the drill from jerking violently.

Speed

Coring bits typically need to be run at
low speeds. A drill with variable speed control is essential.

How to Find the Right Parts


Identify the Drill Model

Find the model number of your drill. This is usually on a sticker on the drill body.2.

Determine Coring Bit Thread

If you already have a 2-inch coring bit, look for markings on the bit that indicate the thread size.3.

Search Online

Search online retailers (like Amazon, Home Depot, etc.) for "coring bit arbor" or "core drill adapter." Include the thread size and chuck size in your search (e.g., "coring bit arbor 5/8-11 to 1/2 inch"). If you have a specific drill model, search for "accessories for [drill model]" or "coring adapter for [drill model]."

Example Search Terms

"Coring bit arbor 1 1/4-7 to 1/2 inch" "Core drill adapter 5/8-11 thread" "Water swivel for core drilling" "Dust shroud for core drill"

In Summary

To help me give you more specific advice, please tell me:


The make and model number of your drill.
What material you intend to core. If you already have a 2-inch coring bit, what is the thread size?

Once I have this information, I can provide more accurate recommendations for the specific parts you'll need. Good luck! Flag for review

Previous Question Next Question