Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Was URD ever allowed to a main breaker?

User: WD40, Location: Philly

Asked on: Thursday, August 7, 2025 at 12:20 pm EDT
Answered on: Thursday, August 7, 2025 at 12:27 pm EDT

Question: Hello group I replaced a loadcenter that had a bad main breaker with a larger one at a townhome in a 55 and over complex and the inspector approved my job but commented the feeder from the meter is in violation, it is 4/0 URD / XLPE from a gang of meter mains out at a parking area.He mentioned another EC had also replaced a panel recently in the complex and there appears to a ongoing issue.The customer was present for this conversation and happens to be on the board of the home owners association.So we opened up the meter packs and all the units were wired the same with URD the codo's are not very old, perhaps 20 years old max.The inspector says this is a construction defect and URD was never allowed by code to enter a building, and has a inferior alloy, what do you all think?My job is approved, done and paid, the inspector is not mandating a fix. I want to get some feedback to the customer per his request.I was able to find the data sheet for the URD cable used: link.

Okay, this is a common situation, especially in older complexes. Let's break down the issue and provide you with informed feedback for your customer

Understanding the Inspector's Concerns:
URD (Underground Residential Distribution) Cable Inside Buildings

The inspector's primary concern is the use of URD cable inside the building structure. Here's why:


Code Compliance

URD cables, like the one in the provided spec sheet, are typically designed and listed for direct burial or installation in underground ducts. While some URD might technically meet the insulation requirements for general wiring (THHN/THWN), it's

not its intended use
and may not be listed for it. The NEC (National Electrical Code) requires that conductors and cables be used only for the purposes for which they are listed and marked (NEC 110.3(B)). Alloy Composition

URD cables are commonly made of aluminum alloy conductors that are less corrosion resistant than typical building wiring. While modern aluminum alloys are much better than those of the past, there's still a potential concern, especially in damp or corrosive environments. In interior applications, copper is typically preferred due to its higher conductivity and corrosion resistance.


Moisture and Gases

URD cables may have insulations that aren't rated for use in interior environments, especially where they might be exposed to gases, fumes, or moisture.

Termination

URD cables sometimes require specific termination methods that may not be readily compatible with standard breakers or lugs.


Fire Resistance

While XLPE insulation is good, URD cable might not have the same fire-resistance properties as conductors specifically listed for building wiring (e.g., THHN/THWN).

"Construction Defect"

The inspector's use of this term implies that the original installation violated the electrical code in effect at the time of construction. Even if the installation passed inspection 20 years ago, codes change, and something that was marginally acceptable then might not be acceptable now.

Key Points to Discuss with Your Customer (the Board Member)


Inspector's Expertise

Emphasize that the inspector is a trained professional responsible for ensuring electrical safety. Their concerns, even without a mandated fix, should be taken seriously.2.

Potential Safety Issues

Explain that while the system is currently functioning, the use of URD inside the building introduces potential long-term safety risks:


Corrosion

Over time, the aluminum conductors could corrode, especially at connections.

Overheating

Improper connections or degradation of the insulation could lead to overheating and potentially a fire.


Code Violation

While the inspector isn't forcing a fix now, future inspections (e.g., for a resale) could flag the issue and require costly remediation.

Insurance

In the event of an electrical fire, the insurance company could investigate the wiring and potentially deny a claim if the URD is determined to be a contributing factor.3.

Long-Term Solution

The best approach is to replace the URD with the proper wire type (likely THHN/THWN in conduit) from the meter pack to each unit's load center. This would involve:


Assessing the Existing Conduit

Determine if the existing conduit is large enough to accommodate the correct size and number of THHN/THWN conductors. If not, new conduit might be needed.

Qualified Electrician

The work must be performed by a licensed and experienced electrician.


Permits and Inspections

Proper permits must be pulled, and the work must be inspected to ensure compliance with current codes.4.

Phased Approach (if budget is a concern)

If a full replacement is too expensive upfront, the HOA could consider a phased approach:

Prioritize Units with Issues

Start by addressing units where there are known electrical problems or where panels are being replaced.


Budget Allocation

Allocate funds in the HOA budget for electrical upgrades over time.5.

HOA's Responsibility

As the HOA, they have a responsibility to maintain the common areas and ensure the safety of all residents. Ignoring the inspector's concerns could expose the HOA to liability.6.

Documentation

Keep a record of the inspector's comments, any discussions with electricians, and any decisions made by the HOA regarding this issue.

Regarding Your Job

You're not at fault. You replaced the panel correctly and to code. You did the right thing by bringing the issue to the customer's attention.* Make it clear that addressing the URD wiring is beyond the scope of your original job.

Final Recommendation

Advise the customer to obtain quotes from multiple qualified electrical contractors to assess the scope of the URD replacement and provide cost estimates. The HOA should then use this information to develop a plan to address the issue in a responsible and cost-effective manner.

Important Disclaimer:
The information provided here is for general informational purposes only. Consult with a licensed and qualified electrician in your area for specific recommendations based on your local codes and conditions. Flag for review

Previous Question Next Question