Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Wireway or Junction Box

User: TwistLock, Location: California

Asked on: Friday, August 8, 2025 at 1:32 pm EDT
Answered on: Friday, August 8, 2025 at 1:33 pm EDT

Question: I used this image mock up for a pre-inspection to make sure inspector was onboard with it. He didn’t have any issues but he also couldn’t guarantee he would be the one coming for final. (He was fine with blocking vent).My question is if the 10x10x6 Nema 3R is ok with this many ‘spliced’ conductors or is it a wire-way subject to derating because more than 30ccc’s.I would be feeding the Junction box with a ≤ 24” piece of 2” EMT. I’m assume 60% fill because of this and zero derating for this section. Rain-Tight listed fitting into top of Nema 3R.If this is allowed I just thought it would be easier than torturing multiple conduits due to KO layout on bottom of panel. Inspector also said he did not consider area below panel to be subject to physical damage fwiw.

Okay, let's break down the electrical code considerations for your proposed junction box setup. Based on your description, here's an analysis of whether it's code-compliant and what you need to consider.

Understanding the Situation You're using a 10x10x6 NEMA 3R junction box (JB) to consolidate conductors from multiple circuits feeding into an electrical panel. The JB will have many spliced conductors, potentially exceeding 30 Current-Carrying Conductors (CCCs). The JB will be fed with a short (≤ 24") section of 2" EMT conduit. You're concerned about fill calculations within the JB and potential derating requirements.

Code Analysis and Concerns1. Junction Box Fill (314.16) Volume Allowance

Your 10x10x6 JB has a specific volume (refer to Table 314.16(A) of the NEC or the manufacturer's specifications for its listed cubic inch capacity).


Conductor Volume

Each conductor entering the JB, each fitting and device inside the JB, and each equipment grounding conductor counts towards the box fill. You must calculate the total volume occupied by all conductors, fittings, and devices in the box.

Wire Size Matters

Larger gauge wires contribute more to the box fill. You need to count each wire and its corresponding volume allowance per 314.16(B). Don't forget that each EGC also counts in the calculation.


Calculations

You must perform these calculations to ensure you're not exceeding the box fill limit. It's tedious, but essential for code compliance. This is the most likely place you'll run into a problem.

Key Question

Can your 10x10x6 box actually accommodate the volume of all those conductors, splices, and grounding wires?2.

Derating (310.15(B)(3)(a))
More than 30 CCCs

You're correct to be concerned about derating. If you have more than 30 CCCs bundled together
inside the junction box, you are subject to derating the ampacity of the conductors.

CCC Definition

A CCC is a conductor that carries current under normal conditions. Neutrals can be CCCs if they carry significant unbalanced load (check NEC 310.15(B)(5)). Grounding conductors are NOT CCCs.

Derating Factors

You'll need to apply the appropriate derating factor from Table 310.15(B)(3)(a) of the NEC based on the number of CCCs in the JB.


Ampacity Adjustment

You must then adjust the ampacity of each conductor based on the derating factor to ensure it can still carry the intended load.3.

Conduit Fill (Chapter 9, Table 1)
Your ≤ 24" EMT

You are correct that, for a nipple (conduit ≤ 24"), you are permitted to fill it up to 60% of its cross-sectional area (Chapter 9, Note 4). This is only for the short piece of conduit entering the junction box.


Conductor Count in Conduit

You need to calculate the total cross-sectional area of all the conductors entering the conduit and ensure it doesn't exceed 60% of the conduit's internal area.4.

Physical Damage (110.27)
The inspector's opinion that the area below the panel is not subject to physical damage is important if that allows you to avoid using rigid conduit. However, you should document this agreement in writing with the inspector to avoid issues with future inspections.5. Workmanship (110.12) The installation must be done in a neat and workmanlike manner. This includes proper support of the junction box, secure connections, and organized conductor routing within the box. A JB crammed full of messy wires will likely fail inspection, even if it technically meets fill requirements.6. Accessibility (314.29) The junction box must remain accessible after installation.

Is it Allowed? Probably,
But...

Based on the information you've provided, using the 10x10x6 NEMA 3R junction box is
potentially allowed, but ONLY if you can demonstrate compliance with the following: Successful Box Fill Calculation

This is the biggest hurdle. You MUST calculate the box fill according to NEC 314.16 and ensure you are not exceeding the maximum allowable volume.

Derating (If Necessary)

If you have more than 30 CCCs, you
must perform derating calculations to ensure the conductors can still carry their intended load.

Conduit Fill

Verify that the conductors entering the 2" EMT nipple do not exceed 60% fill.

Workmanship

Maintain neat and workmanlike installation practices.

Recommendations
1. Perform the Calculations

Before proceeding,
perform the detailed box fill and derating calculations. This will give you a definitive answer as to whether your proposed setup is code-compliant. Don't just guess; do the math!2.

Consider a Larger Box

If your calculations are tight or exceed the limits, consider using a larger junction box. A larger box gives you more room to work and can alleviate box fill concerns. A larger box
may also help with heat dissipation if derating is an issue.3.

Minimize Splices

Consider if there are other methods to avoid creating so many splices. Home runs might be a bit more material but can be less labor and potential inspection issue.4.

Document Everything

Keep a record of your calculations, the inspector's opinion on physical damage, and any other relevant information. This documentation can be helpful during the final inspection.5.

Consult with the Inspector (Again)

It's always a good idea to have another conversation with the inspector (ideally the one who will perform the final inspection) and review your calculations and proposed installation. Get their feedback
before* you complete the work.6.

Consider Wireway
Although similar in nature and sometimes confused with a junction box, wireways are designed to hold conductors that are not spliced within the wireway itself.

Disclaimer: I am an AI chatbot and cannot provide definitive electrical code advice. This information is for educational purposes only. Always consult with a licensed electrician or electrical inspector for guidance on your specific project. They can ensure your installation complies with all applicable codes and regulations. Flag for review

Previous Question Next Question