Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Flickering lights during washer usage

User: Stevenfyeager, Location: United States, Indiana

Asked on: Friday, August 8, 2025 at 1:33 pm EDT
Answered on: Friday, August 8, 2025 at 1:34 pm EDT

Question: LED bulb light fixtures flickering when washer is in use. And they are on separate breakers. Have checked for loose connections. Any suggestions? Thank you.

This is a common problem and can be a bit tricky to diagnose, especially when everything appears to be wired correctly and on separate circuits. Here's a breakdown of possible causes and suggestions to troubleshoot

1. Voltage Fluctuations (Most Likely Culprit):
Voltage Drop

The most likely cause is that the washer, when it's drawing a lot of current (especially during spin cycles or when the motor starts), is causing a temporary voltage drop in your home's electrical system. Even though they're on separate breakers, they ultimately share the same service entrance from the utility company. This voltage sag can be enough to make LEDs flicker because they are very sensitive to voltage changes. Incandescent bulbs tolerate voltage dips much better.


Weak Neutral Connection

A loose or corroded neutral wire anywhere in the circuit, even at the main panel or at the utility company's connection, can cause voltage imbalances. This imbalance can manifest as flickering lights, especially when a large appliance is running.

Troubleshooting Steps (Voltage Fluctuations)



Monitor Voltage at the Light Fixture

Using a multimeter, check the voltage at the light fixture
while the washer is running and causing the flickering. You'll need to do this safely and carefully. If the voltage drops significantly (more than a few volts) when the washer is operating, it strongly suggests a voltage drop problem. If you are not comfortable doing this, please consult a qualified electrician.

Check Voltage at the Washer Outlet

Perform the same voltage test at the washer outlet while it's running. This will help determine if the voltage drop is localized to the washer circuit or affecting the entire house.

Check Voltage at the Main Panel

This is best left to a qualified electrician, but if you're comfortable and know how to do it safely, check the voltage at the main panel while the washer is running. You're looking for consistent voltage on each leg of the service.

2. LED Bulb/Fixture Compatibility



Dimmers

Are the LED lights on a dimmer switch? Not all LEDs are compatible with all dimmers. Using incompatible dimmers can cause flickering, buzzing, or premature bulb failure. Even if you think they are compatible, try replacing the dimmer with a standard switch temporarily to see if the flickering stops.

Bulb Quality/Type

Some cheaper LED bulbs are more susceptible to voltage fluctuations. Try swapping the flickering bulbs with higher-quality LED bulbs, preferably from a reputable brand. Also, try different types of LED bulbs (e.g., dimmable vs. non-dimmable, different wattages).


Fixture Issues

Some light fixtures, especially older ones, might not be fully compatible with LED bulbs. Check the fixture's wattage rating and ensure the LED bulb's wattage is within the specified range.

3. Wiring Issues (Less Likely if on Separate Breakers, but Possible)



Shared Neutral (Multi-Wire Branch Circuit)

Even with separate breakers, if the washer and the lights
inadvertently share a neutral wire (a mistake made during wiring), the current from the washer could be interfering with the lighting circuit. This is dangerous and needs immediate attention.

Loose Neutral Connections (Anywhere)

Loose neutral connections are a common culprit for electrical problems. Even though you checked for loose connections at the fixtures, carefully inspect the following:

At the Main Panel

Again, this should be done by a qualified electrician! Loose neutral connections in the main panel are extremely dangerous.

At Junction Boxes

Check all accessible junction boxes along the circuit for both the washer and the lights.

Washer Outlet

Carefully inspect the wiring at the washer outlet for looseness.


Old or Damaged Wiring

If your home has old wiring (especially aluminum wiring), it could be deteriorating and causing voltage drops.

4. Appliance Issues



Washer Motor Problems

In rare cases, a failing washer motor can create electrical "noise" that interferes with the lighting circuit, even if they're on separate breakers. While not likely, it's worth considering if the flickering started around the same time as any washer performance issues.

Steps to Take


Start with the easiest and safest steps

Try different LED bulbs, especially from a different brand. Temporarily replace any dimmer switches with standard switches.2.

Check the voltage at the light fixture while the washer is running.
If you are not comfortable doing this, contact an electrician.3. If the voltage is dropping significantly, or if you suspect any wiring issues (especially loose neutral connections), IMMEDIATELY call a qualified, licensed electrician. Electrical problems can be dangerous and lead to fires. Do not attempt to troubleshoot or repair wiring if you are not properly trained and equipped.4. If the problem persists even after an electrician has checked the wiring, consider consulting an appliance repair technician to inspect the washer.Important Safety Notes



Electricity is dangerous!
If you're not comfortable working with electricity, hire a qualified electrician. Always turn off the power at the breaker before working on any electrical wiring. Double-check your work. Make sure all connections are tight and secure.* If you smell burning plastic or notice any other signs of electrical problems, immediately turn off the power and call an electrician.

Good luck, and please prioritize safety! Flag for review

Previous Question Next Question