Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Shared transducer

User: ptonsparky, Location: NE (9.06 miles @5.9 Degrees from Winged Horses)

Asked on: Thursday, August 14, 2025 at 11:38 am EDT
Answered on: Thursday, August 14, 2025 at 11:38 am EDT

Question: I have several motors <=15HP that never run at the same time but I would like to get feedback when each does. The output goes to a plc. Not high accuracy requirement but it does initiate a shut down when parameters are exceeded. I would monitor one phase of each motor after its starter. Is there a reason I should not do this?

Monitoring one phase of each motor after its starter to detect if the motor is running is a common and generally acceptable practice, especially given your requirements of non-simultaneous operation and moderate accuracy with shutdown initiation. However, it's crucial to consider potential drawbacks and ensure proper implementation.Here's a breakdown of the reasons why it's generally okay, and what to watch out for

Reasons why it's generally acceptable:
Simple and Cost-Effective

It's a straightforward approach that usually requires minimal hardware (current transformers or voltage sensors, depending on the chosen method).


Clear Indication of Running Status

If the motor is drawing current, it's highly likely it's running. The absence of current indicates it's not.

Suitable for Shut-Down Triggering

The on/off signal is generally reliable enough to initiate a shutdown sequence when parameters exceed limits (though you will need to define these parameter limits).


Non-Simultaneous Operation

The fact that the motors never run simultaneously greatly simplifies the monitoring. You don't have to worry about current overlaps or misinterpretation of aggregate current values.

Potential Drawbacks and Considerations



False Negatives



Open Phase

A blown fuse on a different phase before the starter could leave the monitored phase with no current, even if the motor is trying to run. This would give a false "off" signal, preventing your PLC from detecting a potential problem.

Very Light Load/No Load

If the motor is running but drawing very little current (e.g., idling), your current sensor might not detect enough current to register it as "on." Consider your current transformer or sensor selection to account for this.


Mechanical Failure

If there is a mechanical issue causing the motor to be slow or stalled, but it is not sufficient to trip the starter, the motor may be running but not drawing enough current to be reliably detected.

False Positives



Leakage Current

Depending on the wiring and environment, there might be a small amount of leakage current that could be misinterpreted as the motor running. This is rare but possible.

Sensor Noise

Electrical noise or interference could trigger a false positive.


No Fault Detection

This method only detects if the motor is powered. It doesn't provide information about motor health, overload conditions, overheating, or other potential problems.

Harmonic Distortion

High levels of harmonic distortion in the power system could affect the accuracy of your current or voltage measurements. Consider using true RMS sensors if harmonics are a significant concern.


Sensor Selection



Current Transformers (CTs)

Good for detecting current flow but need to be sized correctly. Too small, and they will saturate; too large, and they will be insensitive to small currents. Make sure the CT has a suitable burden resistor to convert the current into a voltage signal.


Voltage Sensors

Can detect the presence of voltage on the phase.

Wiring and Safety

Proper wiring and insulation are crucial for safety. Working with motor circuits can be dangerous. Ensure that qualified personnel perform the installation.


PLC Programming

The PLC logic should be robust enough to handle potential noise or glitches in the signals. Consider adding filtering or hysteresis to the PLC input signals.

Maintenance

Regularly inspect the sensors and wiring to ensure they are in good condition and functioning correctly.

Recommendations and Best Practices


Choose the Right Sensor

Carefully select the current transformer or voltage sensor based on the expected motor current/voltage range, accuracy requirements, and the type of signal the PLC accepts. Consider a "true RMS" meter for greater accuracy.2.

Proper CT Sizing

Size the CT so that the
primary current range corresponds to the expected motor current. The secondary current is typically 5A or 1A. Choose a CT with a VA rating high enough for the secondary burden (resistance) you will use. Don't open circuit the secondary of a CT while current is flowing in the primary, or very dangerous voltages will be induced.3.

Proper Wiring and Termination

Use appropriate wiring and terminals. Ensure secure connections to prevent loose connections and signal degradation. Use shielded cable for sensor signals to minimize noise.4.

PLC Input Filtering

Implement digital filters in the PLC program to smooth out the input signals and reject noise.5.

Hysteresis

Add hysteresis to the PLC logic to prevent chattering (rapid on/off switching) due to minor current fluctuations. For example, the motor is considered "on" if the current exceeds 5 amps and "off" if it drops below 2 amps.6.

Test and Calibrate

Thoroughly test the system after installation to ensure it's working correctly. Calibrate the sensors if necessary.7.

Safety Precautions

Always follow proper safety procedures when working with electrical equipment.8.

Consider Overcurrent Protection

If not already in place, consider using current monitoring relays (more sophisticated than simple CTs) that can detect overload conditions and trigger alarms or shutdowns. These can give more granular information about motor health.9.

Consider a Soft Starter or Variable Frequency Drive.
If there is not one in place. Inrush Current can lead to false positives.

Alternatives



Smart Motor Protectors/Relays

These devices monitor various motor parameters (current, voltage, temperature) and provide more comprehensive protection and diagnostics.

Power Meters

Measure voltage, current, power, and energy consumption. Provide a more detailed view of motor operation but are more expensive.

In conclusion:


Monitoring one phase after the starter is generally acceptable
if* you address the potential drawbacks and follow best practices. Given that your motors never run simultaneously and that the primary goal is to initiate shutdowns when parameters are exceeded, this is a reasonable approach. However, carefully consider the factors mentioned above and choose the solution that best meets your specific needs and budget.Always prioritize safety and consult with qualified electrical professionals. Flag for review

Previous Question Next Question