Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Noise on Audio System

User: JimS888, Location: California

Asked on: Thursday, August 14, 2025 at 2:56 pm EDT
Answered on: Thursday, August 14, 2025 at 3:02 pm EDT

Question: I have a problem that I've spent months trying to diagnose. Our church recently moved to another building and installed a new audio system. The problem is that there is noise coming out of the audio system. It sounds to me like A/C hum. I seems to be related to the electric guitar and bass. When the system is powered up, the sanctuary lights are on and the guitar is plugged in with the gain turned up, there is an irritating buzz/noise/hum coming out of the speakers.The setup is a multi amplifier rack powering speakers and subwoofers. There is LED and fluorescent house and stage lighting powered through a large Leviton dimmer rack. The dimmer is powered from an underground line that comes from a distribution panel (Panel "S") with a 230 amp 3 phase breaker. Panel S is fed from the main service located in a metal cabinet outside the building. That main service is fed from a transformer owned by the electrical utility.The noise is at its worst when the lights in the sanctuary are at full brightness. When I shut the lights off, the noise is gone. The noise increases as the electrical load increases. When the guitar player faces forward or he turns 180 degrees, facing backward, the noise is somewhat reduced but when he turns to either side the noise gets worse.Tests I've tried:Bypass the dimmer panel by wiring the lights directly into the feed coming from Panel "S" - No improvement in the problemTried Furman power conditioners on each phase in line with the lights. - No improvement in the problemInstalled a Furman Power conditioner in the line feeding one of the amps. - No improvement in the problemTemporarily disconnecting the ground going to the guitar foot controls. - No improvement in the problemTried a dual pickup guitar (Humbucker) - Slight improvement in the problemTemporarily fed the dimmer panel from an isolation transformer that feeds another panel. - No improvement in the problemI've tried several other tests with no success and am stymied, so I am reaching out to this forum for helpI talked with the installers who put in the new audio equipment and they seem very knowledgeable and professional. Several of them quickly said the problem isn't a ground loop but didn't explain their reasoning but it seemed to be based on the fluctuation in the noise when the guitar player turns from side to side. They offered no other explanation.The in house audio tech bought a small device that plugs into an outlet that buzzes and displays line noise and the readings correlate with the noise coming out of the audio system.I also set up a small portable 110 volt generator outside and wired several of the light channels into it, bypassing the dimmer rack. - the noise was gone! This test was just a small number of the lights but those same lights alone running through building power makes noise.I also plugged one of the Furman power conditioners into a nearby 120 volt outlet and ran those same lights and that also seemed to cure the problem.So I think I've eliminated the dimmer rack as a source of the noise and there also seems to be similar noise in other parts of the building when plugging a guitar into a small amp. My current theory is that the problem is emanating from somewhere upstream of Panel "S".Has anyone ever run into anything like this? Any things you can suggest to test?

This is a classic, and frustrating, EMI (Electromagnetic Interference) problem. The fact that a generator and a separate outlet on a different circuit helped isolate the issue strongly suggests the noise is entering through the building's power system, and is being radiated and picked up by the guitar's pickups. The guitar acting as an antenna makes it even more complex. The fluctuating noise when the guitar player turns is a key clue.Here's a breakdown of the likely culprits and a more structured troubleshooting approach

Understanding the Problem:
EMI/RFI (Electromagnetic/Radio Frequency Interference)

This is unwanted energy in the form of radio waves that gets into your audio signal. In this case, it's originating from the building's electrical system, likely due to the lighting.


Ground Loops (Less Likely, but Still a Possibility)

While the sound techs dismiss ground loops, don't completely rule them out. They are usually a steady hum, but they can be exacerbated by other EMI issues.

Antenna Effect

Guitar pickups, especially single-coil pickups, are essentially antennas. They pick up electromagnetic radiation.


Light Dimmers

Even with bypass testing, dimmers are known to generate a lot of EMI, especially older SCR (Silicon Controlled Rectifier) dimmers. Newer LED dimmers can be better, but not always perfect.

Troubleshooting Steps (In Order of Importance)


Isolate the Lighting Circuits



Identify Problematic Circuits

Systematically turn off individual lighting circuits, one at a time, while listening for the hum. This will help pinpoint
which lights are contributing most to the noise.

Lighting Type

What kind of lights are they? Are they traditional incandescent, fluorescent, LED, or a mix? LED and fluorescent lights can be significant sources of noise, especially if they're low-quality or not properly shielded.

Bypass Dimmer Rack Again, Carefully

Instead of just bypassing the
input of the dimmer rack, try completely bypassing it by running new, dedicated circuits directly from Panel "S" to a small number of lights (the ones identified as most problematic). Make absolutely sure there's no connection to the dimmer rack at all. Use a different breaker than is normally used by the dimmer rack. The bypass wiring must be isolated from all other wiring. If this solves the problem, it strongly suggests the dimmer rack, or the wiring to/from it, is radiating noise, even when "bypassed."2.

Grounding and Shielding (Very Important)



Verify Proper Grounding

Make absolutely certain that all audio equipment, the lighting dimmer rack, and electrical panels are properly grounded according to electrical code. A bad or loose ground is a HUGE source of noise. Use a multimeter to verify ground continuity between all metal chassis and electrical panels. Look for low resistance (ideally less than 1 ohm).

Star Grounding

The ideal grounding setup is a "star" ground, where everything is grounded back to a single, central ground point at the main electrical service. This minimizes ground loop potential.


Shielding

Ensure that all audio cables are high-quality, shielded cables. Consider using balanced (XLR) connections whenever possible, as they are more resistant to noise. Check that the metal housing on the XLR connectors are grounded through the cable.

Guitar Shielding

Have the guitar cavity professionally shielded. This involves lining the pickup and control cavities with conductive foil or paint and grounding it to the guitar's ground.


Humbuckers (Already Tried)

Yes, humbuckers help, but it doesn't eliminate the problem.3.

Power Quality (Dig Deeper)



Investigate Voltage Fluctuations

Have an electrician monitor the voltage on all phases of the power coming into Panel "S" and the dimmer rack under various lighting loads. Significant voltage dips or surges could indicate issues with the power supply.


Harmonic Distortion

A power quality analyzer can measure harmonic distortion on the power lines. Dimmers and electronic devices can introduce harmonics, which can cause noise problems.

Neutral Current

Excess current flowing on the neutral wire can be a source of EMI. Have an electrician check the neutral current on Panel "S".


Utility Consultation

Talk to the utility company. Explain the problem and see if they have any insights. They might be able to check the transformer for issues.4.

Physical Layout and Cable Routing



Separation

Keep audio cables as far away as possible from power cables, especially those running to the lights. Run them in separate conduits if possible.


Cable Crossings

If audio and power cables must cross, cross them at right angles to minimize inductive coupling.

Light Fixture Distance

The closer the guitar is to the lights, the more noise will be picked up. Determine the closest distance and try to find a more distant location.


Directional Distance

When you determined that the guitar noise changed as you rotated, that is usually caused by the lights. By rotating, the relative location of the lights is different. Experiment with moving the lights further or closer, or if possible, change the direction the lights point.5.

Ferrite Chokes (Worth a Try)



Ferrite Beads

Clamp-on ferrite chokes (also called ferrite beads) can help suppress high-frequency noise. Try clamping them on the power cables to the dimmer rack, the power cables to the audio amps, and the audio cables near the mixer and amps.6.

Dimmer Rack Inspection



Type of Dimmers

As mentioned earlier, find out what type of dimmers are in the rack. SCR dimmers are the noisiest.

Age and Condition

Are the dimmers old? Older components can degrade and generate more noise.


Dimmer Replacement (Last Resort)

If nothing else works, consider replacing the dimmer rack with a newer, high-quality dimmer rack with filtering designed to minimize EMI.

Why the Installers Might be Wrong About Ground Loops (and why you shouldn't completely dismiss them)

They might be focusing on the fluctuating nature of the noise with guitar movement. True, that's a sign of EMI being picked up by the guitar's pickups. However, a ground loop can amplify EMI issues. A ground loop creates a circuit that acts as an antenna, making the system more susceptible to picking up noise. So, even if the source of the noise is EMI, a ground loop can make it worse.

Next Steps


Start with Grounding and Shielding

This is the most common cause of noise problems and is relatively inexpensive to address.2.

Isolate the Lighting Circuits

Pinpoint which lights are the biggest offenders.3.

Power Quality Analysis

Have an electrician with the right equipment check the power for voltage fluctuations, harmonic distortion, and neutral current.4.

Document Everything:
Keep a detailed record of all tests and changes made, and the results. This will help you track your progress and identify patterns.This is a complex problem, and it may take time and persistence to solve. Good luck! Flag for review

Previous Question Next Question