User: jhemsone, Location: California
Asked on: Thursday, August 14, 2025 at 4:07 pm EDT
Answered on: Thursday, August 14, 2025 at 4:20 pm EDT
Question: Hello, I have a XFMR being fed 2400 VAC which steps down to 480 VAC. XFMR is delta/wye. Secondary feeds two breakers which each control a VFD. How will the fact that I'm not using a "neutral" affect my grounding code? Do I still bond XO to case and still run grounding electrodes like normal. It seems silly but this threw me off. Thanks.
Okay, let's break down grounding for your 2400-480V Delta-Wye transformer feeding VFDs, even though you're not using a neutral for your VFD connections.
Key Principles & Code Considerations NEC Article 250 (Grounding and Bonding) is Paramount
Regardless of whether you are utilizing the neutral conductor, Article 250 dictates the requirements for grounding and bonding systems. Grounding is primarily for personnel safety and equipment protection from fault currents.
Separately Derived System (SDS)
Your delta-wye transformer creates a Separately Derived System (SDS). Because it transforms the voltage and is isolated from the source, it's considered a new power source from a grounding perspective. This means you must establish a grounding electrode system at the transformer.
Grounding Electrode System
You absolutely still need a grounding electrode system connected to the transformer's neutral (X0). This is NON-NEGOTIABLE! It is NOT optional just because you are not connecting to a neutral load on the VFD.
Bonding
The bonding of the X0 to the transformer case is essential for safety. It provides a low-impedance path for fault current to return to the source (the transformer), which in turn helps trip the overcurrent protective device (breaker).
Specific Steps & Why1. Bond X0 to the Transformer Case
Solidly bond the X0 (the neutral point of the wye secondary) to the transformer's metal case. Use a conductor sized according to NEC Table 250.66 (based on the size of your ungrounded conductors). This provides the initial fault current path.
2.
Establish a Grounding Electrode System
Connect a Grounding Electrode Conductor (GEC) from X0 to the Grounding Electrode System
The GEC size is determined by NEC Table 250.66 (again, based on the size of your ungrounded conductors). This conductor connects X0 to the grounding electrode system.
Grounding Electrode System (NEC 250.50)
This consists of one or more of the following (depending on what's available and required by local codes):
Metal Underground Water Pipe
If available, connect to a metallic water pipe that is in direct contact with the earth for 10 feet or more. Supplement this with another electrode, if the water pipe is used as your primary electrode.
Metal Frame of Building
If effectively grounded.
Concrete-Encased Electrode (Ufer Ground)
At least 20 feet of bare copper conductor (at least #4 AWG) encased in concrete foundation (at least 2" thick).
Ground Ring
At least 20 feet of bare copper conductor (at least #2 AWG) buried at least 2.5 feet deep.
Rod and Pipe Electrodes
If other electrodes are not available, drive one or more ground rods or pipes into the earth. Ensure they meet the requirements of NEC 250.53. If using multiple rods, space them at least 6 feet apart. Resistance to ground should be 25 ohms or less (NEC 250.53(B)). If it exceeds 25 ohms, you MUST add another grounding electrode.
3.
Equipment Grounding Conductors (EGCs)
Run Equipment Grounding Conductors with all Circuit Conductors
From your transformer's secondary breaker panel to each VFD. These conductors connect to the VFD's grounding terminal and are sized according to NEC 250.122. They provide a low-impedance path for fault current to return to the source (the transformer) so that breakers trip quickly.
Metal Conduit/Raceway as EGC
If you're using metal conduit (rigid, IMC, EMT) or metal cable trays, they can serve as the EGC if they are properly installed with listed fittings to ensure electrical continuity. However, it's generally a best practice to also run a supplemental wire-type EGC inside the conduit. This offers redundancy and can improve high-frequency grounding performance, which is beneficial for VFD applications.4.
Bonding within the VFD System
Make sure all metal enclosures associated with the VFD, motor, and wiring are properly bonded together. This includes the motor frame itself.
Why This is Important (Even Without Using the Neutral) Fault Current Path
Imagine a fault occurs inside one of your VFDs (e.g., a line conductor shorts to the metal chassis). Without proper grounding, the fault current has no easy path back to the transformer. The voltage on the chassis will rise dangerously, posing a shock hazard to anyone who touches it. The fault current needs a low-impedance path to trip the breaker.
Overvoltage Protection
The grounding system also helps to limit transient overvoltages (e.g., from lightning strikes or switching surges) that could damage equipment.
VFD Performance and EMC
VFDs generate a lot of electrical noise (harmonics, EMI/RFI). Proper grounding helps to contain this noise and prevent it from interfering with other equipment.
In summary: You MUST bond X0 to the case and establish a grounding electrode system per NEC 250, even if you are not using a neutral conductor in your 480V circuits to the VFDs. This is a matter of safety and code compliance. It's not "silly," it's critical. Make sure you use an appropriately sized Grounding Electrode Conductor and Equipment Grounding Conductors based on the NEC tables, and ensure everything is properly bonded. Finally it would be prudent to consult a qualified electrician to ensure you have correctly installed the system. Flag for review