Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Receptacle on end of cabinet counting as small appliance receptacle for countertop?

User: clemver, Location: PA

Asked on: Thursday, August 14, 2025 at 4:35 pm EDT
Answered on: Thursday, August 14, 2025 at 4:35 pm EDT

Question: A GC of mine hit me with a question I'm not sure of, mostly because I've never seen it or had to do it.He has a small 16" cabinet to the right of a sink, that's the only cabinet there. Since it's more than 12" it needs a receptacle. There's no backsplash for this section. Window moulding is basically touching the counter. So it doesn't fall under peninsula. To avoid a pop-up which the homeowner doesn't want, would an outlet in the end panel of the cabinet suffice? I'm looking at 210.52(C)(3)(c) covers countertop and work surfaces(3)covers those receptacle outlet locations. A sub (3) approves below countertop.It does seam pretty cut and dry just wanted to hear some thoughts.

Okay, let's break down the situation and the relevant code to ensure we're on the right track. You're dealing with a tricky spot, and getting it right is important.

Understanding the Requirement

The fundamental issue is the countertop receptacle requirement from NEC 210.52(C). This is designed to ensure readily available receptacles for appliances used on countertops in kitchens. The goal is convenience and safety.

The Situation 16" Cabinet Next to Sink

This cabinet is wide enough to trigger the countertop receptacle requirement.


No Backsplash

This makes a standard backsplash receptacle impossible without modification or creative solutions.

Window Moulding

This further restricts mounting options.


No Pop-Up

The homeowner has specifically rejected pop-up outlets.

NEC 210.52(C)(3) - Below Countertop Receptacles


You're right to focus on 210.52(C)(3). This section is crucial: (3) Receptacle Outlet Location

Receptacle outlets shall be located along the wall at the countertop or work surface, or shall be located at or above, but not more than 20 in. (500 mm) above, the countertop or work surface. Receptacle outlet assemblies listed for use in countertops shall be permitted to be installed in countertops. Receptacle outlets shall not be installed face-up in the work surface or countertop.

Receptacle outlets shall be permitted to be located below the countertop or work surface where all of the following conditions are met



(1) No receptacle outlet is located where the countertop or work surface extends more than 6 in. (150 mm) beyond its support base.
(2) Receptacle outlets are located not more than 12 in. (300 mm) below the countertop or work surface. (3) The countertop or work surface is not an island or peninsular countertop or work surface."

Analysis and AnswerBased on the information you've provided and a careful reading of NEC 210.52(C)(3), an outlet on the end panel of the cabinet is LIKELY acceptable, but with

VERY IMPORTANT CAVEATS:1.

Distance

The key issue is the distance of the receptacle below the countertop surface. The code allows receptacles "below the countertop or work surface" ONLY if they are located

not more than 12 inches (300 mm) below the countertop. You need to measure carefully to ensure the outlet in the end panel of the cabinet meets this 12" requirement. If the top of the cabinet where you'd mount the receptacle is more than 12" below the countertop, this approach is NOT code-compliant.2.

No Overhang

You must ensure that the countertop does not extend more than 6" beyond the cabinet.3.

Not an Island or Peninsula

You've already stated this isn't the case.

Considerations and Best Practices

Local AHJ (Authority Having Jurisdiction)

This is the MOST important point.

ALWAYS consult with your local electrical inspector or AHJ. They have the final say on code interpretation and enforcement in your area. Show them the situation and your proposed solution
before you do the work.

Clarity with Homeowner

While the homeowner doesn't want a pop-up, clearly communicate the limitations and appearance of the end-panel outlet. Show them exactly where it will be.

Receptacle Type

Use a tamper-resistant receptacle, especially if there are children in the home.


Wiring

Ensure the wiring is properly protected and run within the cabinet. Use appropriate fittings and strain relief.

Alternatives (if the end-panel doesn't work)

Carefully Modify the Window Moulding

If possible,
very carefully trim the bottom of the window moulding to allow a standard, low-profile receptacle and cover plate. This might be the least intrusive solution. Get the homeowner's approval.

Low-Profile Backsplash

Explore options for a very thin, low-profile backsplash material (even a few inches high) that would allow for a standard receptacle.

In summary: An outlet on the cabinet end panel could work, provided you meet the 12" distance requirement and the other conditions of 210.52(C)(3). However, you must confirm this with your local AHJ before proceeding. Good luck! Flag for review

Previous Question Next Question