Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: VFD on Line vs. Load Side of Transformer

User: sch, Location: Texas

Asked on: Thursday, August 21, 2025 at 3:45 pm EDT
Answered on: Thursday, August 21, 2025 at 3:54 pm EDT

Question: Hi, I have a 480/277V service and need to run a several hundred horsepower motor at 2300V. My currently intent is to have a 480/277V distribution board, then a 480:2400V transformer, then a VFD, then the motor. This would be switchboard->step-up transformer->VFD->motor. I understand that this drive is very expensive, so I was wondering about placing the VFD between the board and the transformer. This would be switchboard->VFD->step-up transformer->motor. This option would have a sine wave filter. I have heard mixed thoughts on this approach. It would be cheaper but difficult on the transformer due to harmonics or losses.Are there any opinions on this set up? I just want to make sure I am considering all angles and accounting for potential issues.Thank you all in advance.

You've hit upon a common dilemma when dealing with medium-voltage motors and existing low-voltage services. Let's break down the pros and cons of each approach, and then I'll offer some additional considerations

Option 1: Switchboard -> Step-Up Transformer -> VFD -> Motor (Common Approach)
Pros



Standard VFD Design

MV VFDs are designed to operate directly from medium-voltage sources. This is the "normal" configuration for medium-voltage motor applications. You are running a standard high-voltage VFD, which is intended for the output voltages needed.

Transformer Sees Clean Power

The transformer is fed a relatively clean sine wave from the low-voltage switchboard. Transformers are generally more efficient and reliable when fed sinusoidal voltage and current.


Simplified Integration

MV VFD manufacturers often provide comprehensive support and documentation for this type of setup.

Proven Technology

This configuration is widely used and well-understood in the industry.


Cons



Higher VFD Cost

Medium-voltage VFDs are significantly more expensive than low-voltage VFDs.


Larger Footprint

MV VFDs tend to be larger than their LV counterparts.

Potentially Higher Maintenance

MV VFDs may require more specialized maintenance compared to LV VFDs.

Option 2: Switchboard -> VFD -> Step-Up Transformer -> Motor (Less Common, but Potentially Cheaper)
Pros



Lower VFD Cost

LV VFDs are much cheaper than MV VFDs. This is the primary driver for considering this approach.


Smaller Footprint

LV VFDs are smaller, potentially saving space.

Easier Maintenance (Potentially)

LV VFDs may be easier to maintain (depending on complexity and vendor support).


Cons



Transformer Stress

This is the biggest concern. The transformer will be subjected to the harmonics and high-frequency switching components generated by the VFD
unless a very effective sine wave filter is installed before the transformer. Even with a filter, some harmonic content will likely still be present. Harmonics can lead to:

Increased Transformer Losses

Core and copper losses increase due to harmonics, reducing efficiency and potentially causing overheating.

Transformer Overheating

Increased losses lead to increased temperature. Transformers have a limited temperature rating. Exceeding this rating reduces lifespan and can lead to failure.


Transformer Insulation Stress

Harmonic voltages can stress the insulation, shortening the transformer's life.

Resonance Issues

The transformer's inductance and the system capacitance can create resonant frequencies that amplify harmonics, leading to severe voltage distortion and equipment damage.


Sine Wave Filter Requirements

The sine wave filter must be very effective and properly sized to significantly reduce harmonic distortion. This filter adds cost and complexity to the system. A poor filter can make the situation worse.

Transformer Design Considerations

You might need to specify a special transformer designed to handle harmonic loads (K-rated or derated standard transformer). This adds cost.


Voltage Drop and Regulation

The VFD's output voltage may have voltage sags during switching. The transformer needs to handle these variations without causing significant voltage fluctuations at the motor.

Potential for Motor Issues

Even with a sine wave filter, some voltage distortion may reach the motor, potentially leading to:


Increased Motor Heating

Harmonics cause additional losses in the motor.

Reduced Motor Life

Insulation stress from harmonics shortens motor life.


Torque Pulsations

Harmonics can cause uneven torque production, leading to vibration and noise.

Complexity and Integration Challenges

This configuration is less common, so integration and commissioning may be more challenging. Getting the VFD, filter, and transformer to work optimally together requires careful engineering and coordination.


Limited Vendor Support

You might find that VFD and transformer manufacturers are less willing to support this non-standard configuration, potentially leading to finger-pointing if problems arise.

Transformer Inrush Current

VFD output harmonics will be amplified during transformer inrush current, which could potentially lead to overcurrent protection tripping or component failures.

Key Considerations and Recommendations


Transformer Specifications

If you pursue option 2, you must consult with transformer manufacturers and provide them with a detailed harmonic profile of the VFD's output (with and without the filter). They can then recommend a suitable transformer (K-rated, derated, or custom designed) and provide guidance on filter requirements.2.

Sine Wave Filter Performance

Get detailed specifications for the sine wave filter. Ask for THDv (Total Harmonic Voltage Distortion) and THDi (Total Harmonic Current Distortion) figures under various load conditions. Aim for very low THDv (ideally below 5%) at the transformer output.3.

Motor Considerations

Consult with the motor manufacturer to ensure that the motor can tolerate any remaining harmonic distortion. Derate the motor if necessary.4.

System Modeling

Consider performing a power system simulation (using software like ETAP or SKM) to analyze the harmonic behavior of the system and ensure that there are no resonance issues.5.

Warranty and Support

Discuss warranty and support with both the VFD and transformer manufacturers. Ensure they are willing to support the configuration and clearly define responsibility for any issues.6.

Expert Consultation

Hire a qualified electrical engineer experienced in power quality and motor drive systems to review your design and provide recommendations. This is crucial due to the non-standard nature of the second option.7.

Cost Analysis

Perform a thorough cost analysis that includes not only the initial purchase price but also installation, commissioning, maintenance, and potential downtime costs. The cheaper option might end up being more expensive in the long run if it leads to increased maintenance or equipment failures.8.

Efficiency

Compare the overall efficiency of both systems. The increased losses in the transformer in option 2 may offset some of the cost savings from the cheaper VFD.

My Recommendation

While option 2
might seem appealing from a cost perspective, it introduces significant technical challenges and risks.

I strongly recommend sticking with option 1 (Switchboard -> Step-Up Transformer -> VFD -> Motor) unless you have a very compelling reason to deviate from the standard approach and are willing to invest heavily in engineering and specialized equipment.


The increased reliability, simplified integration, and better vendor support of option 1 will likely save you money in the long run. The peace of mind that comes from using a proven and well-supported configuration is also valuable.If you
still* want to explore option 2, proceed with extreme caution and involve experienced engineers who can thoroughly evaluate the risks and ensure that the system is properly designed and protected. Don't base the decision solely on initial cost; consider the total cost of ownership.Good luck with your project! Flag for review

Previous Question Next Question